diff --git a/drivers/net/pfe/base/cbus.h b/drivers/net/pfe/base/cbus.h
new file mode 100644
index 000000000..2de2bfa5d
--- /dev/null
+++ b/drivers/net/pfe/base/cbus.h
@@ -0,0 +1,66 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#ifndef _CBUS_H_
+#define _CBUS_H_
+
+#include <compat.h>
+
+#define EMAC1_BASE_ADDR	(CBUS_BASE_ADDR + 0x200000)
+#define EGPI1_BASE_ADDR	(CBUS_BASE_ADDR + 0x210000)
+#define EMAC2_BASE_ADDR	(CBUS_BASE_ADDR + 0x220000)
+#define EGPI2_BASE_ADDR	(CBUS_BASE_ADDR + 0x230000)
+#define BMU1_BASE_ADDR	(CBUS_BASE_ADDR + 0x240000)
+#define BMU2_BASE_ADDR	(CBUS_BASE_ADDR + 0x250000)
+#define ARB_BASE_ADDR	(CBUS_BASE_ADDR + 0x260000)
+#define DDR_CONFIG_BASE_ADDR	(CBUS_BASE_ADDR + 0x270000)
+#define HIF_BASE_ADDR	(CBUS_BASE_ADDR + 0x280000)
+#define HGPI_BASE_ADDR	(CBUS_BASE_ADDR + 0x290000)
+#define LMEM_BASE_ADDR	(CBUS_BASE_ADDR + 0x300000)
+#define LMEM_SIZE	0x10000
+#define LMEM_END	(LMEM_BASE_ADDR + LMEM_SIZE)
+#define TMU_CSR_BASE_ADDR	(CBUS_BASE_ADDR + 0x310000)
+#define CLASS_CSR_BASE_ADDR	(CBUS_BASE_ADDR + 0x320000)
+#define HIF_NOCPY_BASE_ADDR	(CBUS_BASE_ADDR + 0x350000)
+#define UTIL_CSR_BASE_ADDR	(CBUS_BASE_ADDR + 0x360000)
+#define CBUS_GPT_BASE_ADDR	(CBUS_BASE_ADDR + 0x370000)
+
+/*
+ * defgroup XXX_MEM_ACCESS_ADDR PE memory access through CSR
+ * XXX_MEM_ACCESS_ADDR register bit definitions.
+ */
+#define PE_MEM_ACCESS_WRITE	BIT(31)	/* Internal Memory Write. */
+#define PE_MEM_ACCESS_IMEM	BIT(15)
+#define PE_MEM_ACCESS_DMEM	BIT(16)
+
+/* Byte Enables of the Internal memory access. These are interpred in BE */
+#define PE_MEM_ACCESS_BYTE_ENABLE(offset, size)	\
+	({ typeof(size) size_ = (size);		\
+	(((BIT(size_) - 1) << (4 - (offset) - (size_))) & 0xf) << 24; })
+
+#include "cbus/emac_mtip.h"
+#include "cbus/gpi.h"
+#include "cbus/bmu.h"
+#include "cbus/hif.h"
+#include "cbus/tmu_csr.h"
+#include "cbus/class_csr.h"
+#include "cbus/hif_nocpy.h"
+#include "cbus/util_csr.h"
+
+/* PFE cores states */
+#define CORE_DISABLE	0x00000000
+#define CORE_ENABLE	0x00000001
+#define CORE_SW_RESET	0x00000002
+
+/* LMEM defines */
+#define LMEM_HDR_SIZE	0x0010
+#define LMEM_BUF_SIZE_LN2	0x7
+#define LMEM_BUF_SIZE	BIT(LMEM_BUF_SIZE_LN2)
+
+/* DDR defines */
+#define DDR_HDR_SIZE	0x0100
+#define DDR_BUF_SIZE_LN2	0xb
+#define DDR_BUF_SIZE	BIT(DDR_BUF_SIZE_LN2)
+
+#endif /* _CBUS_H_ */
diff --git a/drivers/net/pfe/base/cbus/bmu.h b/drivers/net/pfe/base/cbus/bmu.h
new file mode 100644
index 000000000..c2a4a2813
--- /dev/null
+++ b/drivers/net/pfe/base/cbus/bmu.h
@@ -0,0 +1,41 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#ifndef _BMU_H_
+#define _BMU_H_
+
+#define BMU_VERSION	0x000
+#define BMU_CTRL	0x004
+#define BMU_UCAST_CONFIG	0x008
+#define BMU_UCAST_BASE_ADDR	0x00c
+#define BMU_BUF_SIZE	0x010
+#define BMU_BUF_CNT	0x014
+#define BMU_THRES	0x018
+#define BMU_INT_SRC	0x020
+#define BMU_INT_ENABLE	0x024
+#define BMU_ALLOC_CTRL	0x030
+#define BMU_FREE_CTRL	0x034
+#define BMU_FREE_ERR_ADDR	0x038
+#define BMU_CURR_BUF_CNT	0x03c
+#define BMU_MCAST_CNT	0x040
+#define BMU_MCAST_ALLOC_CTRL	0x044
+#define BMU_REM_BUF_CNT	0x048
+#define BMU_LOW_WATERMARK	0x050
+#define BMU_HIGH_WATERMARK	0x054
+#define BMU_INT_MEM_ACCESS	0x100
+
+struct BMU_CFG {
+	unsigned long baseaddr;
+	u32 count;
+	u32 size;
+	u32 low_watermark;
+	u32 high_watermark;
+};
+
+#define BMU1_BUF_SIZE	LMEM_BUF_SIZE_LN2
+#define BMU2_BUF_SIZE	DDR_BUF_SIZE_LN2
+
+#define BMU2_MCAST_ALLOC_CTRL	(BMU2_BASE_ADDR + BMU_MCAST_ALLOC_CTRL)
+
+#endif /* _BMU_H_ */
diff --git a/drivers/net/pfe/base/cbus/class_csr.h b/drivers/net/pfe/base/cbus/class_csr.h
new file mode 100644
index 000000000..70af01a27
--- /dev/null
+++ b/drivers/net/pfe/base/cbus/class_csr.h
@@ -0,0 +1,277 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#ifndef _CLASS_CSR_H_
+#define _CLASS_CSR_H_
+
+#include <compat.h>
+
+/* @file class_csr.h.
+ * class_csr - block containing all the classifier control and status register.
+ * Mapped on CBUS and accessible from all PE's and ARM.
+ */
+#define CLASS_VERSION	(CLASS_CSR_BASE_ADDR + 0x000)
+#define CLASS_TX_CTRL	(CLASS_CSR_BASE_ADDR + 0x004)
+#define CLASS_INQ_PKTPTR	(CLASS_CSR_BASE_ADDR + 0x010)
+
+/* (ddr_hdr_size[24:16], lmem_hdr_size[5:0]) */
+#define CLASS_HDR_SIZE	(CLASS_CSR_BASE_ADDR + 0x014)
+
+/* LMEM header size for the Classifier block.\ Data in the LMEM
+ * is written from this offset.
+ */
+#define CLASS_HDR_SIZE_LMEM(off)	((off) & 0x3f)
+
+/* DDR header size for the Classifier block.\ Data in the DDR
+ * is written from this offset.
+ */
+#define CLASS_HDR_SIZE_DDR(off)	(((off) & 0x1ff) << 16)
+
+#define CLASS_PE0_QB_DM_ADDR0	(CLASS_CSR_BASE_ADDR + 0x020)
+
+/* DMEM address of first [15:0] and second [31:16] buffers on QB side. */
+#define CLASS_PE0_QB_DM_ADDR1	(CLASS_CSR_BASE_ADDR + 0x024)
+
+/* DMEM address of third [15:0] and fourth [31:16] buffers on QB side. */
+#define CLASS_PE0_RO_DM_ADDR0	(CLASS_CSR_BASE_ADDR + 0x060)
+
+/* DMEM address of first [15:0] and second [31:16] buffers on RO side. */
+#define CLASS_PE0_RO_DM_ADDR1	(CLASS_CSR_BASE_ADDR + 0x064)
+
+/* DMEM address of third [15:0] and fourth [31:16] buffers on RO side. */
+
+/* @name Class PE memory access. Allows external PE's and HOST to
+ * read/write PMEM/DMEM memory ranges for each classifier PE.
+ */
+/* {sr_pe_mem_cmd[31], csr_pe_mem_wren[27:24], csr_pe_mem_addr[23:0]},
+ * See \ref XXX_MEM_ACCESS_ADDR for details.
+ */
+#define CLASS_MEM_ACCESS_ADDR	(CLASS_CSR_BASE_ADDR + 0x100)
+
+/* Internal Memory Access Write Data [31:0] */
+#define CLASS_MEM_ACCESS_WDATA	(CLASS_CSR_BASE_ADDR + 0x104)
+
+/* Internal Memory Access Read Data [31:0] */
+#define CLASS_MEM_ACCESS_RDATA	(CLASS_CSR_BASE_ADDR + 0x108)
+#define CLASS_TM_INQ_ADDR	(CLASS_CSR_BASE_ADDR + 0x114)
+#define CLASS_PE_STATUS	(CLASS_CSR_BASE_ADDR + 0x118)
+
+#define CLASS_PHY1_RX_PKTS	(CLASS_CSR_BASE_ADDR + 0x11c)
+#define CLASS_PHY1_TX_PKTS	(CLASS_CSR_BASE_ADDR + 0x120)
+#define CLASS_PHY1_LP_FAIL_PKTS	(CLASS_CSR_BASE_ADDR + 0x124)
+#define CLASS_PHY1_INTF_FAIL_PKTS	(CLASS_CSR_BASE_ADDR + 0x128)
+#define CLASS_PHY1_INTF_MATCH_PKTS	(CLASS_CSR_BASE_ADDR + 0x12c)
+#define CLASS_PHY1_L3_FAIL_PKTS	(CLASS_CSR_BASE_ADDR + 0x130)
+#define CLASS_PHY1_V4_PKTS	(CLASS_CSR_BASE_ADDR + 0x134)
+#define CLASS_PHY1_V6_PKTS	(CLASS_CSR_BASE_ADDR + 0x138)
+#define CLASS_PHY1_CHKSUM_ERR_PKTS	(CLASS_CSR_BASE_ADDR + 0x13c)
+#define CLASS_PHY1_TTL_ERR_PKTS	(CLASS_CSR_BASE_ADDR + 0x140)
+#define CLASS_PHY2_RX_PKTS	(CLASS_CSR_BASE_ADDR + 0x144)
+#define CLASS_PHY2_TX_PKTS	(CLASS_CSR_BASE_ADDR + 0x148)
+#define CLASS_PHY2_LP_FAIL_PKTS	(CLASS_CSR_BASE_ADDR + 0x14c)
+#define CLASS_PHY2_INTF_FAIL_PKTS	(CLASS_CSR_BASE_ADDR + 0x150)
+#define CLASS_PHY2_INTF_MATCH_PKTS	(CLASS_CSR_BASE_ADDR + 0x154)
+#define CLASS_PHY2_L3_FAIL_PKTS	(CLASS_CSR_BASE_ADDR + 0x158)
+#define CLASS_PHY2_V4_PKTS	(CLASS_CSR_BASE_ADDR + 0x15c)
+#define CLASS_PHY2_V6_PKTS	(CLASS_CSR_BASE_ADDR + 0x160)
+#define CLASS_PHY2_CHKSUM_ERR_PKTS	(CLASS_CSR_BASE_ADDR + 0x164)
+#define CLASS_PHY2_TTL_ERR_PKTS	(CLASS_CSR_BASE_ADDR + 0x168)
+#define CLASS_PHY3_RX_PKTS	(CLASS_CSR_BASE_ADDR + 0x16c)
+#define CLASS_PHY3_TX_PKTS	(CLASS_CSR_BASE_ADDR + 0x170)
+#define CLASS_PHY3_LP_FAIL_PKTS	(CLASS_CSR_BASE_ADDR + 0x174)
+#define CLASS_PHY3_INTF_FAIL_PKTS	(CLASS_CSR_BASE_ADDR + 0x178)
+#define CLASS_PHY3_INTF_MATCH_PKTS	(CLASS_CSR_BASE_ADDR + 0x17c)
+#define CLASS_PHY3_L3_FAIL_PKTS	(CLASS_CSR_BASE_ADDR + 0x180)
+#define CLASS_PHY3_V4_PKTS	(CLASS_CSR_BASE_ADDR + 0x184)
+#define CLASS_PHY3_V6_PKTS	(CLASS_CSR_BASE_ADDR + 0x188)
+#define CLASS_PHY3_CHKSUM_ERR_PKTS	(CLASS_CSR_BASE_ADDR + 0x18c)
+#define CLASS_PHY3_TTL_ERR_PKTS	(CLASS_CSR_BASE_ADDR + 0x190)
+#define CLASS_PHY1_ICMP_PKTS	(CLASS_CSR_BASE_ADDR + 0x194)
+#define CLASS_PHY1_IGMP_PKTS	(CLASS_CSR_BASE_ADDR + 0x198)
+#define CLASS_PHY1_TCP_PKTS	(CLASS_CSR_BASE_ADDR + 0x19c)
+#define CLASS_PHY1_UDP_PKTS	(CLASS_CSR_BASE_ADDR + 0x1a0)
+#define CLASS_PHY2_ICMP_PKTS	(CLASS_CSR_BASE_ADDR + 0x1a4)
+#define CLASS_PHY2_IGMP_PKTS	(CLASS_CSR_BASE_ADDR + 0x1a8)
+#define CLASS_PHY2_TCP_PKTS	(CLASS_CSR_BASE_ADDR + 0x1ac)
+#define CLASS_PHY2_UDP_PKTS	(CLASS_CSR_BASE_ADDR + 0x1b0)
+#define CLASS_PHY3_ICMP_PKTS	(CLASS_CSR_BASE_ADDR + 0x1b4)
+#define CLASS_PHY3_IGMP_PKTS	(CLASS_CSR_BASE_ADDR + 0x1b8)
+#define CLASS_PHY3_TCP_PKTS	(CLASS_CSR_BASE_ADDR + 0x1bc)
+#define CLASS_PHY3_UDP_PKTS	(CLASS_CSR_BASE_ADDR + 0x1c0)
+#define CLASS_PHY4_ICMP_PKTS	(CLASS_CSR_BASE_ADDR + 0x1c4)
+#define CLASS_PHY4_IGMP_PKTS	(CLASS_CSR_BASE_ADDR + 0x1c8)
+#define CLASS_PHY4_TCP_PKTS	(CLASS_CSR_BASE_ADDR + 0x1cc)
+#define CLASS_PHY4_UDP_PKTS	(CLASS_CSR_BASE_ADDR + 0x1d0)
+#define CLASS_PHY4_RX_PKTS	(CLASS_CSR_BASE_ADDR + 0x1d4)
+#define CLASS_PHY4_TX_PKTS	(CLASS_CSR_BASE_ADDR + 0x1d8)
+#define CLASS_PHY4_LP_FAIL_PKTS	(CLASS_CSR_BASE_ADDR + 0x1dc)
+#define CLASS_PHY4_INTF_FAIL_PKTS	(CLASS_CSR_BASE_ADDR + 0x1e0)
+#define CLASS_PHY4_INTF_MATCH_PKTS	(CLASS_CSR_BASE_ADDR + 0x1e4)
+#define CLASS_PHY4_L3_FAIL_PKTS	(CLASS_CSR_BASE_ADDR + 0x1e8)
+#define CLASS_PHY4_V4_PKTS	(CLASS_CSR_BASE_ADDR + 0x1ec)
+#define CLASS_PHY4_V6_PKTS	(CLASS_CSR_BASE_ADDR + 0x1f0)
+#define CLASS_PHY4_CHKSUM_ERR_PKTS	(CLASS_CSR_BASE_ADDR + 0x1f4)
+#define CLASS_PHY4_TTL_ERR_PKTS	(CLASS_CSR_BASE_ADDR + 0x1f8)
+
+#define CLASS_PE_SYS_CLK_RATIO	(CLASS_CSR_BASE_ADDR + 0x200)
+#define CLASS_AFULL_THRES	(CLASS_CSR_BASE_ADDR + 0x204)
+#define CLASS_GAP_BETWEEN_READS	(CLASS_CSR_BASE_ADDR + 0x208)
+#define CLASS_MAX_BUF_CNT	(CLASS_CSR_BASE_ADDR + 0x20c)
+#define CLASS_TSQ_FIFO_THRES	(CLASS_CSR_BASE_ADDR + 0x210)
+#define CLASS_TSQ_MAX_CNT	(CLASS_CSR_BASE_ADDR + 0x214)
+#define CLASS_IRAM_DATA_0	(CLASS_CSR_BASE_ADDR + 0x218)
+#define CLASS_IRAM_DATA_1	(CLASS_CSR_BASE_ADDR + 0x21c)
+#define CLASS_IRAM_DATA_2	(CLASS_CSR_BASE_ADDR + 0x220)
+#define CLASS_IRAM_DATA_3	(CLASS_CSR_BASE_ADDR + 0x224)
+
+#define CLASS_BUS_ACCESS_ADDR	(CLASS_CSR_BASE_ADDR + 0x228)
+
+#define CLASS_BUS_ACCESS_WDATA	(CLASS_CSR_BASE_ADDR + 0x22c)
+#define CLASS_BUS_ACCESS_RDATA	(CLASS_CSR_BASE_ADDR + 0x230)
+
+/* (route_entry_size[9:0], route_hash_size[23:16]
+ * (this is actually ln2(size)))
+ */
+#define CLASS_ROUTE_HASH_ENTRY_SIZE	(CLASS_CSR_BASE_ADDR + 0x234)
+
+#define CLASS_ROUTE_ENTRY_SIZE(size)	 ((size) & 0x1ff)
+#define CLASS_ROUTE_HASH_SIZE(hash_bits) (((hash_bits) & 0xff) << 16)
+
+#define CLASS_ROUTE_TABLE_BASE	(CLASS_CSR_BASE_ADDR + 0x238)
+
+#define CLASS_ROUTE_MULTI	(CLASS_CSR_BASE_ADDR + 0x23c)
+#define CLASS_SMEM_OFFSET	(CLASS_CSR_BASE_ADDR + 0x240)
+#define CLASS_LMEM_BUF_SIZE	(CLASS_CSR_BASE_ADDR + 0x244)
+#define CLASS_VLAN_ID	(CLASS_CSR_BASE_ADDR + 0x248)
+#define CLASS_BMU1_BUF_FREE	(CLASS_CSR_BASE_ADDR + 0x24c)
+#define CLASS_USE_TMU_INQ	(CLASS_CSR_BASE_ADDR + 0x250)
+#define CLASS_VLAN_ID1	(CLASS_CSR_BASE_ADDR + 0x254)
+
+#define CLASS_BUS_ACCESS_BASE	(CLASS_CSR_BASE_ADDR + 0x258)
+#define CLASS_BUS_ACCESS_BASE_MASK	(0xFF000000)
+/* bit 31:24 of PE peripheral address are stored in CLASS_BUS_ACCESS_BASE */
+
+#define CLASS_HIF_PARSE	(CLASS_CSR_BASE_ADDR + 0x25c)
+
+#define CLASS_HOST_PE0_GP	(CLASS_CSR_BASE_ADDR + 0x260)
+#define CLASS_PE0_GP	(CLASS_CSR_BASE_ADDR + 0x264)
+#define CLASS_HOST_PE1_GP	(CLASS_CSR_BASE_ADDR + 0x268)
+#define CLASS_PE1_GP	(CLASS_CSR_BASE_ADDR + 0x26c)
+#define CLASS_HOST_PE2_GP	(CLASS_CSR_BASE_ADDR + 0x270)
+#define CLASS_PE2_GP	(CLASS_CSR_BASE_ADDR + 0x274)
+#define CLASS_HOST_PE3_GP	(CLASS_CSR_BASE_ADDR + 0x278)
+#define CLASS_PE3_GP	(CLASS_CSR_BASE_ADDR + 0x27c)
+#define CLASS_HOST_PE4_GP	(CLASS_CSR_BASE_ADDR + 0x280)
+#define CLASS_PE4_GP	(CLASS_CSR_BASE_ADDR + 0x284)
+#define CLASS_HOST_PE5_GP	(CLASS_CSR_BASE_ADDR + 0x288)
+#define CLASS_PE5_GP	(CLASS_CSR_BASE_ADDR + 0x28c)
+
+#define CLASS_PE_INT_SRC	(CLASS_CSR_BASE_ADDR + 0x290)
+#define CLASS_PE_INT_ENABLE	(CLASS_CSR_BASE_ADDR + 0x294)
+
+#define CLASS_TPID0_TPID1	(CLASS_CSR_BASE_ADDR + 0x298)
+#define CLASS_TPID2	(CLASS_CSR_BASE_ADDR + 0x29c)
+
+#define CLASS_L4_CHKSUM_ADDR	(CLASS_CSR_BASE_ADDR + 0x2a0)
+
+#define CLASS_PE0_DEBUG	(CLASS_CSR_BASE_ADDR + 0x2a4)
+#define CLASS_PE1_DEBUG	(CLASS_CSR_BASE_ADDR + 0x2a8)
+#define CLASS_PE2_DEBUG	(CLASS_CSR_BASE_ADDR + 0x2ac)
+#define CLASS_PE3_DEBUG	(CLASS_CSR_BASE_ADDR + 0x2b0)
+#define CLASS_PE4_DEBUG	(CLASS_CSR_BASE_ADDR + 0x2b4)
+#define CLASS_PE5_DEBUG	(CLASS_CSR_BASE_ADDR + 0x2b8)
+
+#define CLASS_STATE	(CLASS_CSR_BASE_ADDR + 0x2bc)
+
+/* CLASS defines */
+#define CLASS_PBUF_SIZE	0x100	/* Fixed by hardware */
+#define CLASS_PBUF_HEADER_OFFSET	0x80	/* Can be configured */
+
+/* Can be configured */
+#define CLASS_PBUF0_BASE_ADDR	0x000
+/* Can be configured */
+#define CLASS_PBUF1_BASE_ADDR	(CLASS_PBUF0_BASE_ADDR + CLASS_PBUF_SIZE)
+/* Can be configured */
+#define CLASS_PBUF2_BASE_ADDR	(CLASS_PBUF1_BASE_ADDR + CLASS_PBUF_SIZE)
+/* Can be configured */
+#define CLASS_PBUF3_BASE_ADDR	(CLASS_PBUF2_BASE_ADDR + CLASS_PBUF_SIZE)
+
+#define CLASS_PBUF0_HEADER_BASE_ADDR	(CLASS_PBUF0_BASE_ADDR + \
+						CLASS_PBUF_HEADER_OFFSET)
+#define CLASS_PBUF1_HEADER_BASE_ADDR	(CLASS_PBUF1_BASE_ADDR + \
+						CLASS_PBUF_HEADER_OFFSET)
+#define CLASS_PBUF2_HEADER_BASE_ADDR	(CLASS_PBUF2_BASE_ADDR + \
+						CLASS_PBUF_HEADER_OFFSET)
+#define CLASS_PBUF3_HEADER_BASE_ADDR	(CLASS_PBUF3_BASE_ADDR + \
+						CLASS_PBUF_HEADER_OFFSET)
+
+#define CLASS_PE0_RO_DM_ADDR0_VAL	((CLASS_PBUF1_BASE_ADDR << 16) | \
+						CLASS_PBUF0_BASE_ADDR)
+#define CLASS_PE0_RO_DM_ADDR1_VAL	((CLASS_PBUF3_BASE_ADDR << 16) | \
+						CLASS_PBUF2_BASE_ADDR)
+
+#define CLASS_PE0_QB_DM_ADDR0_VAL	((CLASS_PBUF1_HEADER_BASE_ADDR << 16) |\
+						CLASS_PBUF0_HEADER_BASE_ADDR)
+#define CLASS_PE0_QB_DM_ADDR1_VAL	((CLASS_PBUF3_HEADER_BASE_ADDR << 16) |\
+						CLASS_PBUF2_HEADER_BASE_ADDR)
+
+#define CLASS_ROUTE_SIZE	128
+#define CLASS_MAX_ROUTE_SIZE	256
+#define CLASS_ROUTE_HASH_BITS	20
+#define CLASS_ROUTE_HASH_MASK	(BIT(CLASS_ROUTE_HASH_BITS) - 1)
+
+/* Can be configured */
+#define	CLASS_ROUTE0_BASE_ADDR	0x400
+/* Can be configured */
+#define CLASS_ROUTE1_BASE_ADDR	(CLASS_ROUTE0_BASE_ADDR + CLASS_ROUTE_SIZE)
+/* Can be configured */
+#define CLASS_ROUTE2_BASE_ADDR	(CLASS_ROUTE1_BASE_ADDR + CLASS_ROUTE_SIZE)
+/* Can be configured */
+#define CLASS_ROUTE3_BASE_ADDR	(CLASS_ROUTE2_BASE_ADDR + CLASS_ROUTE_SIZE)
+
+#define CLASS_SA_SIZE	128
+#define CLASS_IPSEC_SA0_BASE_ADDR	0x600
+/* not used */
+#define CLASS_IPSEC_SA1_BASE_ADDR  (CLASS_IPSEC_SA0_BASE_ADDR + CLASS_SA_SIZE)
+/* not used */
+#define CLASS_IPSEC_SA2_BASE_ADDR  (CLASS_IPSEC_SA1_BASE_ADDR + CLASS_SA_SIZE)
+/* not used */
+#define CLASS_IPSEC_SA3_BASE_ADDR  (CLASS_IPSEC_SA2_BASE_ADDR + CLASS_SA_SIZE)
+
+/* generic purpose free dmem buffer, last portion of 2K dmem pbuf */
+#define CLASS_GP_DMEM_BUF_SIZE	(2048 - (CLASS_PBUF_SIZE * 4) - \
+				(CLASS_ROUTE_SIZE * 4) - (CLASS_SA_SIZE))
+#define CLASS_GP_DMEM_BUF	((void *)(CLASS_IPSEC_SA0_BASE_ADDR + \
+					CLASS_SA_SIZE))
+
+#define TWO_LEVEL_ROUTE		BIT(0)
+#define PHYNO_IN_HASH		BIT(1)
+#define HW_ROUTE_FETCH		BIT(3)
+#define HW_BRIDGE_FETCH		BIT(5)
+#define IP_ALIGNED		BIT(6)
+#define ARC_HIT_CHECK_EN	BIT(7)
+#define CLASS_TOE		BIT(11)
+#define HASH_NORMAL		(0 << 12)
+#define HASH_CRC_PORT		BIT(12)
+#define HASH_CRC_IP		(2 << 12)
+#define HASH_CRC_PORT_IP	(3 << 12)
+#define QB2BUS_LE		BIT(15)
+
+#define TCP_CHKSUM_DROP		BIT(0)
+#define UDP_CHKSUM_DROP		BIT(1)
+#define IPV4_CHKSUM_DROP	BIT(9)
+
+/*CLASS_HIF_PARSE bits*/
+#define HIF_PKT_CLASS_EN	BIT(0)
+#define HIF_PKT_OFFSET(ofst)	(((ofst) & 0xF) << 1)
+
+struct class_cfg {
+	u32 toe_mode;
+	unsigned long route_table_baseaddr;
+	u32 route_table_hash_bits;
+	u32 pe_sys_clk_ratio;
+	u32 resume;
+};
+
+#endif /* _CLASS_CSR_H_ */
diff --git a/drivers/net/pfe/base/cbus/emac_mtip.h b/drivers/net/pfe/base/cbus/emac_mtip.h
new file mode 100644
index 000000000..ea54e2ee5
--- /dev/null
+++ b/drivers/net/pfe/base/cbus/emac_mtip.h
@@ -0,0 +1,231 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#ifndef _EMAC_H_
+#define _EMAC_H_
+
+/* This file is for Ethernet MAC registers and offsets
+ */
+
+#include <linux/ethtool.h>
+
+#define EMAC_IEVENT_REG		0x004
+#define EMAC_IMASK_REG		0x008
+#define EMAC_R_DES_ACTIVE_REG	0x010
+#define EMAC_X_DES_ACTIVE_REG	0x014
+#define EMAC_ECNTRL_REG		0x024
+#define EMAC_MII_DATA_REG	0x040
+#define EMAC_MII_CTRL_REG	0x044
+#define EMAC_MIB_CTRL_STS_REG	0x064
+#define EMAC_RCNTRL_REG		0x084
+#define EMAC_TCNTRL_REG		0x0C4
+#define EMAC_PHY_ADDR_LOW	0x0E4
+#define EMAC_PHY_ADDR_HIGH	0x0E8
+#define EMAC_GAUR		0x120
+#define EMAC_GALR		0x124
+#define EMAC_TFWR_STR_FWD	0x144
+#define EMAC_RX_SECTION_FULL	0x190
+#define EMAC_RX_SECTION_EMPTY	0x194
+#define EMAC_TX_SECTION_EMPTY	0x1A0
+#define EMAC_TRUNC_FL		0x1B0
+
+#define RMON_T_DROP	0x200 /* Count of frames not cntd correctly */
+#define RMON_T_PACKETS	0x204 /* RMON TX packet count */
+#define RMON_T_BC_PKT	0x208 /* RMON TX broadcast pkts */
+#define RMON_T_MC_PKT	0x20c /* RMON TX multicast pkts */
+#define RMON_T_CRC_ALIGN	0x210 /* RMON TX pkts with CRC align err */
+#define RMON_T_UNDERSIZE	0x214 /* RMON TX pkts < 64 bytes, good CRC */
+#define RMON_T_OVERSIZE	0x218 /* RMON TX pkts > MAX_FL bytes good CRC */
+#define RMON_T_FRAG	0x21c /* RMON TX pkts < 64 bytes, bad CRC */
+#define RMON_T_JAB	0x220 /* RMON TX pkts > MAX_FL bytes, bad CRC */
+#define RMON_T_COL	0x224 /* RMON TX collision count */
+#define RMON_T_P64	0x228 /* RMON TX 64 byte pkts */
+#define RMON_T_P65TO127	0x22c /* RMON TX 65 to 127 byte pkts */
+#define RMON_T_P128TO255	0x230 /* RMON TX 128 to 255 byte pkts */
+#define RMON_T_P256TO511	0x234 /* RMON TX 256 to 511 byte pkts */
+#define RMON_T_P512TO1023	0x238 /* RMON TX 512 to 1023 byte pkts */
+#define RMON_T_P1024TO2047	0x23c /* RMON TX 1024 to 2047 byte pkts */
+#define RMON_T_P_GTE2048	0x240 /* RMON TX pkts > 2048 bytes */
+#define RMON_T_OCTETS	0x244 /* RMON TX octets */
+#define IEEE_T_DROP	0x248 /* Count of frames not counted crtly */
+#define IEEE_T_FRAME_OK	0x24c /* Frames tx'd OK */
+#define IEEE_T_1COL	0x250 /* Frames tx'd with single collision */
+#define IEEE_T_MCOL	0x254 /* Frames tx'd with multiple collision */
+#define IEEE_T_DEF	0x258 /* Frames tx'd after deferral delay */
+#define IEEE_T_LCOL	0x25c /* Frames tx'd with late collision */
+#define IEEE_T_EXCOL	0x260 /* Frames tx'd with excesv collisions */
+#define IEEE_T_MACERR	0x264 /* Frames tx'd with TX FIFO underrun */
+#define IEEE_T_CSERR	0x268 /* Frames tx'd with carrier sense err */
+#define IEEE_T_SQE	0x26c /* Frames tx'd with SQE err */
+#define IEEE_T_FDXFC	0x270 /* Flow control pause frames tx'd */
+#define IEEE_T_OCTETS_OK	0x274 /* Octet count for frames tx'd w/o err */
+#define RMON_R_PACKETS	0x284 /* RMON RX packet count */
+#define RMON_R_BC_PKT	0x288 /* RMON RX broadcast pkts */
+#define RMON_R_MC_PKT	0x28c /* RMON RX multicast pkts */
+#define RMON_R_CRC_ALIGN	0x290 /* RMON RX pkts with CRC alignment err */
+#define RMON_R_UNDERSIZE	0x294 /* RMON RX pkts < 64 bytes, good CRC */
+#define RMON_R_OVERSIZE	0x298 /* RMON RX pkts > MAX_FL bytes good CRC */
+#define RMON_R_FRAG	0x29c /* RMON RX pkts < 64 bytes, bad CRC */
+#define RMON_R_JAB	0x2a0 /* RMON RX pkts > MAX_FL bytes, bad CRC */
+#define RMON_R_RESVD_O	0x2a4 /* Reserved */
+#define RMON_R_P64	0x2a8 /* RMON RX 64 byte pkts */
+#define RMON_R_P65TO127	0x2ac /* RMON RX 65 to 127 byte pkts */
+#define RMON_R_P128TO255	0x2b0 /* RMON RX 128 to 255 byte pkts */
+#define RMON_R_P256TO511	0x2b4 /* RMON RX 256 to 511 byte pkts */
+#define RMON_R_P512TO1023	0x2b8 /* RMON RX 512 to 1023 byte pkts */
+#define RMON_R_P1024TO2047	0x2bc /* RMON RX 1024 to 2047 byte pkts */
+#define RMON_R_P_GTE2048	0x2c0 /* RMON RX pkts > 2048 bytes */
+#define RMON_R_OCTETS	0x2c4 /* RMON RX octets */
+#define IEEE_R_DROP	0x2c8 /* Count frames not counted correctly */
+#define IEEE_R_FRAME_OK	0x2cc /* Frames rx'd OK */
+#define IEEE_R_CRC	0x2d0 /* Frames rx'd with CRC err */
+#define IEEE_R_ALIGN	0x2d4 /* Frames rx'd with alignment err */
+#define IEEE_R_MACERR	0x2d8 /* Receive FIFO overflow count */
+#define IEEE_R_FDXFC	0x2dc /* Flow control pause frames rx'd */
+#define IEEE_R_OCTETS_OK	0x2e0 /* Octet cnt for frames rx'd w/o err */
+
+#define EMAC_SMAC_0_0	0x500 /*Supplemental MAC Address 0 (RW).*/
+#define EMAC_SMAC_0_1	0x504 /*Supplemental MAC Address 0 (RW).*/
+
+/* GEMAC definitions and settings */
+
+#define EMAC_PORT_0	0
+#define EMAC_PORT_1	1
+
+/* GEMAC Bit definitions */
+#define EMAC_IEVENT_HBERR		 0x80000000
+#define EMAC_IEVENT_BABR		 0x40000000
+#define EMAC_IEVENT_BABT		 0x20000000
+#define EMAC_IEVENT_GRA			 0x10000000
+#define EMAC_IEVENT_TXF			 0x08000000
+#define EMAC_IEVENT_TXB			 0x04000000
+#define EMAC_IEVENT_RXF			 0x02000000
+#define EMAC_IEVENT_RXB			 0x01000000
+#define EMAC_IEVENT_MII			 0x00800000
+#define EMAC_IEVENT_EBERR		 0x00400000
+#define EMAC_IEVENT_LC			 0x00200000
+#define EMAC_IEVENT_RL			 0x00100000
+#define EMAC_IEVENT_UN			 0x00080000
+
+#define EMAC_IMASK_HBERR                 0x80000000
+#define EMAC_IMASK_BABR                  0x40000000
+#define EMAC_IMASKT_BABT                 0x20000000
+#define EMAC_IMASK_GRA                   0x10000000
+#define EMAC_IMASKT_TXF                  0x08000000
+#define EMAC_IMASK_TXB                   0x04000000
+#define EMAC_IMASKT_RXF                  0x02000000
+#define EMAC_IMASK_RXB                   0x01000000
+#define EMAC_IMASK_MII                   0x00800000
+#define EMAC_IMASK_EBERR                 0x00400000
+#define EMAC_IMASK_LC                    0x00200000
+#define EMAC_IMASKT_RL                   0x00100000
+#define EMAC_IMASK_UN                    0x00080000
+
+#define EMAC_RCNTRL_MAX_FL_SHIFT         16
+#define EMAC_RCNTRL_LOOP                 0x00000001
+#define EMAC_RCNTRL_DRT                  0x00000002
+#define EMAC_RCNTRL_MII_MODE             0x00000004
+#define EMAC_RCNTRL_PROM                 0x00000008
+#define EMAC_RCNTRL_BC_REJ               0x00000010
+#define EMAC_RCNTRL_FCE                  0x00000020
+#define EMAC_RCNTRL_RGMII                0x00000040
+#define EMAC_RCNTRL_SGMII                0x00000080
+#define EMAC_RCNTRL_RMII                 0x00000100
+#define EMAC_RCNTRL_RMII_10T             0x00000200
+#define EMAC_RCNTRL_CRC_FWD		 0x00004000
+
+#define EMAC_TCNTRL_GTS                  0x00000001
+#define EMAC_TCNTRL_HBC                  0x00000002
+#define EMAC_TCNTRL_FDEN                 0x00000004
+#define EMAC_TCNTRL_TFC_PAUSE            0x00000008
+#define EMAC_TCNTRL_RFC_PAUSE            0x00000010
+
+#define EMAC_ECNTRL_RESET                0x00000001      /* reset the EMAC */
+#define EMAC_ECNTRL_ETHER_EN             0x00000002      /* enable the EMAC */
+#define EMAC_ECNTRL_MAGIC_ENA		 0x00000004
+#define EMAC_ECNTRL_SLEEP		 0x00000008
+#define EMAC_ECNTRL_SPEED                0x00000020
+#define EMAC_ECNTRL_DBSWAP               0x00000100
+
+#define EMAC_X_WMRK_STRFWD               0x00000100
+
+#define EMAC_X_DES_ACTIVE_TDAR           0x01000000
+#define EMAC_R_DES_ACTIVE_RDAR           0x01000000
+
+#define EMAC_RX_SECTION_EMPTY_V		0x00010006
+/*
+ * The possible operating speeds of the MAC, currently supporting 10, 100 and
+ * 1000Mb modes.
+ */
+enum mac_speed {SPEED_10M, SPEED_100M, SPEED_1000M, SPEED_1000M_PCS};
+
+/* MII-related definitios */
+#define EMAC_MII_DATA_ST         0x40000000      /* Start of frame delimiter */
+#define EMAC_MII_DATA_OP_RD      0x20000000      /* Perform a read operation */
+#define EMAC_MII_DATA_OP_CL45_RD 0x30000000      /* Perform a read operation */
+#define EMAC_MII_DATA_OP_WR      0x10000000      /* Perform a write operation */
+#define EMAC_MII_DATA_OP_CL45_WR 0x10000000      /* Perform a write operation */
+#define EMAC_MII_DATA_PA_MSK     0x0f800000      /* PHY Address field mask */
+#define EMAC_MII_DATA_RA_MSK     0x007c0000      /* PHY Register field mask */
+#define EMAC_MII_DATA_TA         0x00020000      /* Turnaround */
+#define EMAC_MII_DATA_DATAMSK    0x0000ffff      /* PHY data field */
+
+#define EMAC_MII_DATA_RA_SHIFT   18      /* MII Register address bits */
+#define EMAC_MII_DATA_RA_MASK	 0x1F      /* MII Register address mask */
+#define EMAC_MII_DATA_PA_SHIFT   23      /* MII PHY address bits */
+#define EMAC_MII_DATA_PA_MASK    0x1F      /* MII PHY address mask */
+
+#define EMAC_MII_DATA_RA(v) (((v) & EMAC_MII_DATA_RA_MASK) << \
+				EMAC_MII_DATA_RA_SHIFT)
+#define EMAC_MII_DATA_PA(v) (((v) & EMAC_MII_DATA_RA_MASK) << \
+				EMAC_MII_DATA_PA_SHIFT)
+#define EMAC_MII_DATA(v)    ((v) & 0xffff)
+
+#define EMAC_MII_SPEED_SHIFT	1
+#define EMAC_HOLDTIME_SHIFT	8
+#define EMAC_HOLDTIME_MASK	0x7
+#define EMAC_HOLDTIME(v)	(((v) & EMAC_HOLDTIME_MASK) << \
+					EMAC_HOLDTIME_SHIFT)
+
+/*
+ * The Address organisation for the MAC device.  All addresses are split into
+ * two 32-bit register fields.  The first one (bottom) is the lower 32-bits of
+ * the address and the other field are the high order bits - this may be 16-bits
+ * in the case of MAC addresses, or 32-bits for the hash address.
+ * In terms of memory storage, the first item (bottom) is assumed to be at a
+ * lower address location than 'top'. i.e. top should be at address location of
+ * 'bottom' + 4 bytes.
+ */
+struct pfe_mac_addr {
+	u32 bottom;     /* Lower 32-bits of address. */
+	u32 top;        /* Upper 32-bits of address. */
+};
+
+/*
+ * The following is the organisation of the address filters section of the MAC
+ * registers.  The Cadence MAC contains four possible specific address match
+ * addresses, if an incoming frame corresponds to any one of these four
+ * addresses then the frame will be copied to memory.
+ * It is not necessary for all four of the address match registers to be
+ * programmed, this is application dependent.
+ */
+struct spec_addr {
+	struct pfe_mac_addr one;        /* Specific address register 1. */
+	struct pfe_mac_addr two;        /* Specific address register 2. */
+	struct pfe_mac_addr three;      /* Specific address register 3. */
+	struct pfe_mac_addr four;       /* Specific address register 4. */
+};
+
+struct gemac_cfg {
+	u32 mode;
+	u32 speed;
+	u32 duplex;
+};
+
+/* EMAC Hash size */
+#define EMAC_HASH_REG_BITS       64
+
+#define EMAC_SPEC_ADDR_MAX	4
+
+#endif /* _EMAC_H_ */
diff --git a/drivers/net/pfe/base/cbus/gpi.h b/drivers/net/pfe/base/cbus/gpi.h
new file mode 100644
index 000000000..60d834323
--- /dev/null
+++ b/drivers/net/pfe/base/cbus/gpi.h
@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#ifndef _GPI_H_
+#define _GPI_H_
+
+/* Generic Packet Interface:The generic packet interface block interfaces
+ * to block like ethernet, Host interfac and covert data into WSP internal
+ * structures
+ */
+
+#define GPI_VERSION	0x00
+#define GPI_CTRL	0x04
+#define GPI_RX_CONFIG	0x08
+#define GPI_HDR_SIZE	0x0c
+#define GPI_BUF_SIZE	0x10
+#define GPI_LMEM_ALLOC_ADDR	0x14
+#define GPI_LMEM_FREE_ADDR	0x18
+#define GPI_DDR_ALLOC_ADDR	0x1c
+#define GPI_DDR_FREE_ADDR	0x20
+#define GPI_CLASS_ADDR	0x24
+#define GPI_DRX_FIFO	0x28
+#define GPI_TRX_FIFO	0x2c
+#define GPI_INQ_PKTPTR	0x30
+#define GPI_DDR_DATA_OFFSET	0x34
+#define GPI_LMEM_DATA_OFFSET	0x38
+#define GPI_TMLF_TX	0x4c
+#define GPI_DTX_ASEQ	0x50
+#define GPI_FIFO_STATUS	0x54
+#define GPI_FIFO_DEBUG	0x58
+#define GPI_TX_PAUSE_TIME	0x5c
+#define GPI_LMEM_SEC_BUF_DATA_OFFSET	0x60
+#define GPI_DDR_SEC_BUF_DATA_OFFSET	0x64
+#define GPI_TOE_CHKSUM_EN	0x68
+#define GPI_OVERRUN_DROPCNT	0x6c
+#define GPI_CSR_MTIP_PAUSE_REG		0x74
+#define GPI_CSR_MTIP_PAUSE_QUANTUM	0x78
+#define GPI_CSR_RX_CNT			0x7c
+#define GPI_CSR_TX_CNT			0x80
+#define GPI_CSR_DEBUG1			0x84
+#define GPI_CSR_DEBUG2			0x88
+
+struct gpi_cfg {
+	u32 lmem_rtry_cnt;
+	u32 tmlf_txthres;
+	u32 aseq_len;
+	u32 mtip_pause_reg;
+};
+
+/* GPI commons defines */
+#define GPI_LMEM_BUF_EN	0x1
+#define GPI_DDR_BUF_EN	0x1
+
+/* EGPI 1 defines */
+#define EGPI1_LMEM_RTRY_CNT	0x40
+#define EGPI1_TMLF_TXTHRES	0xBC
+#define EGPI1_ASEQ_LEN	0x50
+
+/* EGPI 2 defines */
+#define EGPI2_LMEM_RTRY_CNT	0x40
+#define EGPI2_TMLF_TXTHRES	0xBC
+#define EGPI2_ASEQ_LEN	0x40
+
+/* EGPI 3 defines */
+#define EGPI3_LMEM_RTRY_CNT	0x40
+#define EGPI3_TMLF_TXTHRES	0xBC
+#define EGPI3_ASEQ_LEN	0x40
+
+/* HGPI defines */
+#define HGPI_LMEM_RTRY_CNT	0x40
+#define HGPI_TMLF_TXTHRES	0xBC
+#define HGPI_ASEQ_LEN	0x40
+
+#define EGPI_PAUSE_TIME		0x000007D0
+#define EGPI_PAUSE_ENABLE	0x40000000
+#endif /* _GPI_H_ */
diff --git a/drivers/net/pfe/base/cbus/hif.h b/drivers/net/pfe/base/cbus/hif.h
new file mode 100644
index 000000000..bffd3d923
--- /dev/null
+++ b/drivers/net/pfe/base/cbus/hif.h
@@ -0,0 +1,86 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#ifndef _HIF_H_
+#define _HIF_H_
+
+/* @file hif.h.
+ * hif - PFE hif block control and status register.
+ * Mapped on CBUS and accessible from all PE's and ARM.
+ */
+#define HIF_VERSION	(HIF_BASE_ADDR + 0x00)
+#define HIF_TX_CTRL	(HIF_BASE_ADDR + 0x04)
+#define HIF_TX_CURR_BD_ADDR	(HIF_BASE_ADDR + 0x08)
+#define HIF_TX_ALLOC	(HIF_BASE_ADDR + 0x0c)
+#define HIF_TX_BDP_ADDR	(HIF_BASE_ADDR + 0x10)
+#define HIF_TX_STATUS	(HIF_BASE_ADDR + 0x14)
+#define HIF_RX_CTRL	(HIF_BASE_ADDR + 0x20)
+#define HIF_RX_BDP_ADDR	(HIF_BASE_ADDR + 0x24)
+#define HIF_RX_STATUS	(HIF_BASE_ADDR + 0x30)
+#define HIF_INT_SRC	(HIF_BASE_ADDR + 0x34)
+#define HIF_INT_ENABLE	(HIF_BASE_ADDR + 0x38)
+#define HIF_POLL_CTRL	(HIF_BASE_ADDR + 0x3c)
+#define HIF_RX_CURR_BD_ADDR	(HIF_BASE_ADDR + 0x40)
+#define HIF_RX_ALLOC	(HIF_BASE_ADDR + 0x44)
+#define HIF_TX_DMA_STATUS	(HIF_BASE_ADDR + 0x48)
+#define HIF_RX_DMA_STATUS	(HIF_BASE_ADDR + 0x4c)
+#define HIF_INT_COAL	(HIF_BASE_ADDR + 0x50)
+
+/* HIF_INT_SRC/ HIF_INT_ENABLE control bits */
+#define HIF_INT		BIT(0)
+#define HIF_RXBD_INT	BIT(1)
+#define HIF_RXPKT_INT	BIT(2)
+#define HIF_TXBD_INT	BIT(3)
+#define HIF_TXPKT_INT	BIT(4)
+
+/* HIF_TX_CTRL bits */
+#define HIF_CTRL_DMA_EN			BIT(0)
+#define HIF_CTRL_BDP_POLL_CTRL_EN	BIT(1)
+#define HIF_CTRL_BDP_CH_START_WSTB	BIT(2)
+
+/* HIF_RX_STATUS bits */
+#define BDP_CSR_RX_DMA_ACTV     BIT(16)
+
+/* HIF_INT_ENABLE bits */
+#define HIF_INT_EN		BIT(0)
+#define HIF_RXBD_INT_EN		BIT(1)
+#define HIF_RXPKT_INT_EN	BIT(2)
+#define HIF_TXBD_INT_EN		BIT(3)
+#define HIF_TXPKT_INT_EN	BIT(4)
+
+/* HIF_POLL_CTRL bits*/
+#define HIF_RX_POLL_CTRL_CYCLE	0x0400
+#define HIF_TX_POLL_CTRL_CYCLE	0x0400
+
+/* HIF_INT_COAL bits*/
+#define HIF_INT_COAL_ENABLE	BIT(31)
+
+/* Buffer descriptor control bits */
+#define BD_CTRL_BUFLEN_MASK	0x3fff
+#define BD_BUF_LEN(x)	((x) & BD_CTRL_BUFLEN_MASK)
+#define BD_CTRL_CBD_INT_EN	BIT(16)
+#define BD_CTRL_PKT_INT_EN	BIT(17)
+#define BD_CTRL_LIFM		BIT(18)
+#define BD_CTRL_LAST_BD		BIT(19)
+#define BD_CTRL_DIR		BIT(20)
+#define BD_CTRL_LMEM_CPY	BIT(21) /* Valid only for HIF_NOCPY */
+#define BD_CTRL_PKT_XFER	BIT(24)
+#define BD_CTRL_DESC_EN		BIT(31)
+#define BD_CTRL_PARSE_DISABLE	BIT(25)
+#define BD_CTRL_BRFETCH_DISABLE	BIT(26)
+#define BD_CTRL_RTFETCH_DISABLE	BIT(27)
+
+/* Buffer descriptor status bits*/
+#define BD_STATUS_CONN_ID(x)	((x) & 0xffff)
+#define BD_STATUS_DIR_PROC_ID	BIT(16)
+#define BD_STATUS_CONN_ID_EN	BIT(17)
+#define BD_STATUS_PE2PROC_ID(x)	(((x) & 7) << 18)
+#define BD_STATUS_LE_DATA	BIT(21)
+#define BD_STATUS_CHKSUM_EN	BIT(22)
+
+/* HIF Buffer descriptor status bits */
+#define DIR_PROC_ID	BIT(16)
+#define PROC_ID(id)	((id) << 18)
+
+#endif /* _HIF_H_ */
diff --git a/drivers/net/pfe/base/cbus/hif_nocpy.h b/drivers/net/pfe/base/cbus/hif_nocpy.h
new file mode 100644
index 000000000..8c627b1c7
--- /dev/null
+++ b/drivers/net/pfe/base/cbus/hif_nocpy.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#ifndef _HIF_NOCPY_H_
+#define _HIF_NOCPY_H_
+
+#define HIF_NOCPY_VERSION	(HIF_NOCPY_BASE_ADDR + 0x00)
+#define HIF_NOCPY_TX_CTRL	(HIF_NOCPY_BASE_ADDR + 0x04)
+#define HIF_NOCPY_TX_CURR_BD_ADDR	(HIF_NOCPY_BASE_ADDR + 0x08)
+#define HIF_NOCPY_TX_ALLOC	(HIF_NOCPY_BASE_ADDR + 0x0c)
+#define HIF_NOCPY_TX_BDP_ADDR	(HIF_NOCPY_BASE_ADDR + 0x10)
+#define HIF_NOCPY_TX_STATUS	(HIF_NOCPY_BASE_ADDR + 0x14)
+#define HIF_NOCPY_RX_CTRL	(HIF_NOCPY_BASE_ADDR + 0x20)
+#define HIF_NOCPY_RX_BDP_ADDR	(HIF_NOCPY_BASE_ADDR + 0x24)
+#define HIF_NOCPY_RX_STATUS	(HIF_NOCPY_BASE_ADDR + 0x30)
+#define HIF_NOCPY_INT_SRC	(HIF_NOCPY_BASE_ADDR + 0x34)
+#define HIF_NOCPY_INT_ENABLE	(HIF_NOCPY_BASE_ADDR + 0x38)
+#define HIF_NOCPY_POLL_CTRL	(HIF_NOCPY_BASE_ADDR + 0x3c)
+#define HIF_NOCPY_RX_CURR_BD_ADDR	(HIF_NOCPY_BASE_ADDR + 0x40)
+#define HIF_NOCPY_RX_ALLOC	(HIF_NOCPY_BASE_ADDR + 0x44)
+#define HIF_NOCPY_TX_DMA_STATUS	(HIF_NOCPY_BASE_ADDR + 0x48)
+#define HIF_NOCPY_RX_DMA_STATUS	(HIF_NOCPY_BASE_ADDR + 0x4c)
+#define HIF_NOCPY_RX_INQ0_PKTPTR	(HIF_NOCPY_BASE_ADDR + 0x50)
+#define HIF_NOCPY_RX_INQ1_PKTPTR	(HIF_NOCPY_BASE_ADDR + 0x54)
+#define HIF_NOCPY_TX_PORT_NO	(HIF_NOCPY_BASE_ADDR + 0x60)
+#define HIF_NOCPY_LMEM_ALLOC_ADDR	(HIF_NOCPY_BASE_ADDR + 0x64)
+#define HIF_NOCPY_CLASS_ADDR	(HIF_NOCPY_BASE_ADDR + 0x68)
+#define HIF_NOCPY_TMU_PORT0_ADDR	(HIF_NOCPY_BASE_ADDR + 0x70)
+#define HIF_NOCPY_TMU_PORT1_ADDR	(HIF_NOCPY_BASE_ADDR + 0x74)
+#define HIF_NOCPY_TMU_PORT2_ADDR	(HIF_NOCPY_BASE_ADDR + 0x7c)
+#define HIF_NOCPY_TMU_PORT3_ADDR	(HIF_NOCPY_BASE_ADDR + 0x80)
+#define HIF_NOCPY_TMU_PORT4_ADDR	(HIF_NOCPY_BASE_ADDR + 0x84)
+#define HIF_NOCPY_INT_COAL	(HIF_NOCPY_BASE_ADDR + 0x90)
+
+#endif /* _HIF_NOCPY_H_ */
diff --git a/drivers/net/pfe/base/cbus/tmu_csr.h b/drivers/net/pfe/base/cbus/tmu_csr.h
new file mode 100644
index 000000000..2f4a62a76
--- /dev/null
+++ b/drivers/net/pfe/base/cbus/tmu_csr.h
@@ -0,0 +1,154 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#ifndef _TMU_CSR_H_
+#define _TMU_CSR_H_
+
+#define TMU_VERSION	(TMU_CSR_BASE_ADDR + 0x000)
+#define TMU_INQ_WATERMARK	(TMU_CSR_BASE_ADDR + 0x004)
+#define TMU_PHY_INQ_PKTPTR	(TMU_CSR_BASE_ADDR + 0x008)
+#define TMU_PHY_INQ_PKTINFO	(TMU_CSR_BASE_ADDR + 0x00c)
+#define TMU_PHY_INQ_FIFO_CNT	(TMU_CSR_BASE_ADDR + 0x010)
+#define TMU_SYS_GENERIC_CONTROL	(TMU_CSR_BASE_ADDR + 0x014)
+#define TMU_SYS_GENERIC_STATUS	(TMU_CSR_BASE_ADDR + 0x018)
+#define TMU_SYS_GEN_CON0	(TMU_CSR_BASE_ADDR + 0x01c)
+#define TMU_SYS_GEN_CON1	(TMU_CSR_BASE_ADDR + 0x020)
+#define TMU_SYS_GEN_CON2	(TMU_CSR_BASE_ADDR + 0x024)
+#define TMU_SYS_GEN_CON3	(TMU_CSR_BASE_ADDR + 0x028)
+#define TMU_SYS_GEN_CON4	(TMU_CSR_BASE_ADDR + 0x02c)
+#define TMU_TEQ_DISABLE_DROPCHK	(TMU_CSR_BASE_ADDR + 0x030)
+#define TMU_TEQ_CTRL	(TMU_CSR_BASE_ADDR + 0x034)
+#define TMU_TEQ_QCFG	(TMU_CSR_BASE_ADDR + 0x038)
+#define TMU_TEQ_DROP_STAT	(TMU_CSR_BASE_ADDR + 0x03c)
+#define TMU_TEQ_QAVG	(TMU_CSR_BASE_ADDR + 0x040)
+#define TMU_TEQ_WREG_PROB	(TMU_CSR_BASE_ADDR + 0x044)
+#define TMU_TEQ_TRANS_STAT	(TMU_CSR_BASE_ADDR + 0x048)
+#define TMU_TEQ_HW_PROB_CFG0	(TMU_CSR_BASE_ADDR + 0x04c)
+#define TMU_TEQ_HW_PROB_CFG1	(TMU_CSR_BASE_ADDR + 0x050)
+#define TMU_TEQ_HW_PROB_CFG2	(TMU_CSR_BASE_ADDR + 0x054)
+#define TMU_TEQ_HW_PROB_CFG3	(TMU_CSR_BASE_ADDR + 0x058)
+#define TMU_TEQ_HW_PROB_CFG4	(TMU_CSR_BASE_ADDR + 0x05c)
+#define TMU_TEQ_HW_PROB_CFG5	(TMU_CSR_BASE_ADDR + 0x060)
+#define TMU_TEQ_HW_PROB_CFG6	(TMU_CSR_BASE_ADDR + 0x064)
+#define TMU_TEQ_HW_PROB_CFG7	(TMU_CSR_BASE_ADDR + 0x068)
+#define TMU_TEQ_HW_PROB_CFG8	(TMU_CSR_BASE_ADDR + 0x06c)
+#define TMU_TEQ_HW_PROB_CFG9	(TMU_CSR_BASE_ADDR + 0x070)
+#define TMU_TEQ_HW_PROB_CFG10	(TMU_CSR_BASE_ADDR + 0x074)
+#define TMU_TEQ_HW_PROB_CFG11	(TMU_CSR_BASE_ADDR + 0x078)
+#define TMU_TEQ_HW_PROB_CFG12	(TMU_CSR_BASE_ADDR + 0x07c)
+#define TMU_TEQ_HW_PROB_CFG13	(TMU_CSR_BASE_ADDR + 0x080)
+#define TMU_TEQ_HW_PROB_CFG14	(TMU_CSR_BASE_ADDR + 0x084)
+#define TMU_TEQ_HW_PROB_CFG15	(TMU_CSR_BASE_ADDR + 0x088)
+#define TMU_TEQ_HW_PROB_CFG16	(TMU_CSR_BASE_ADDR + 0x08c)
+#define TMU_TEQ_HW_PROB_CFG17	(TMU_CSR_BASE_ADDR + 0x090)
+#define TMU_TEQ_HW_PROB_CFG18	(TMU_CSR_BASE_ADDR + 0x094)
+#define TMU_TEQ_HW_PROB_CFG19	(TMU_CSR_BASE_ADDR + 0x098)
+#define TMU_TEQ_HW_PROB_CFG20	(TMU_CSR_BASE_ADDR + 0x09c)
+#define TMU_TEQ_HW_PROB_CFG21	(TMU_CSR_BASE_ADDR + 0x0a0)
+#define TMU_TEQ_HW_PROB_CFG22	(TMU_CSR_BASE_ADDR + 0x0a4)
+#define TMU_TEQ_HW_PROB_CFG23	(TMU_CSR_BASE_ADDR + 0x0a8)
+#define TMU_TEQ_HW_PROB_CFG24	(TMU_CSR_BASE_ADDR + 0x0ac)
+#define TMU_TEQ_HW_PROB_CFG25	(TMU_CSR_BASE_ADDR + 0x0b0)
+#define TMU_TDQ_IIFG_CFG	(TMU_CSR_BASE_ADDR + 0x0b4)
+/* [9:0] Scheduler Enable for each of the scheduler in the TDQ.
+ * This is a global Enable for all schedulers in PHY0
+ */
+#define TMU_TDQ0_SCH_CTRL	(TMU_CSR_BASE_ADDR + 0x0b8)
+
+#define TMU_LLM_CTRL	(TMU_CSR_BASE_ADDR + 0x0bc)
+#define TMU_LLM_BASE_ADDR	(TMU_CSR_BASE_ADDR + 0x0c0)
+#define TMU_LLM_QUE_LEN	(TMU_CSR_BASE_ADDR + 0x0c4)
+#define TMU_LLM_QUE_HEADPTR	(TMU_CSR_BASE_ADDR + 0x0c8)
+#define TMU_LLM_QUE_TAILPTR	(TMU_CSR_BASE_ADDR + 0x0cc)
+#define TMU_LLM_QUE_DROPCNT	(TMU_CSR_BASE_ADDR + 0x0d0)
+#define TMU_INT_EN	(TMU_CSR_BASE_ADDR + 0x0d4)
+#define TMU_INT_SRC	(TMU_CSR_BASE_ADDR + 0x0d8)
+#define TMU_INQ_STAT	(TMU_CSR_BASE_ADDR + 0x0dc)
+#define TMU_CTRL	(TMU_CSR_BASE_ADDR + 0x0e0)
+
+/* [31] Mem Access Command. 0 = Internal Memory Read, 1 = Internal memory
+ * Write [27:24] Byte Enables of the Internal memory access [23:0] Address of
+ * the internal memory. This address is used to access both the PM and DM of
+ * all the PE's
+ */
+#define TMU_MEM_ACCESS_ADDR	(TMU_CSR_BASE_ADDR + 0x0e4)
+
+/* Internal Memory Access Write Data */
+#define TMU_MEM_ACCESS_WDATA	(TMU_CSR_BASE_ADDR + 0x0e8)
+/* Internal Memory Access Read Data. The commands are blocked
+ * at the mem_access only
+ */
+#define TMU_MEM_ACCESS_RDATA	(TMU_CSR_BASE_ADDR + 0x0ec)
+
+/* [31:0] PHY0 in queue address (must be initialized with one of the
+ * xxx_INQ_PKTPTR cbus addresses)
+ */
+#define TMU_PHY0_INQ_ADDR	(TMU_CSR_BASE_ADDR + 0x0f0)
+/* [31:0] PHY1 in queue address (must be initialized with one of the
+ * xxx_INQ_PKTPTR cbus addresses)
+ */
+#define TMU_PHY1_INQ_ADDR	(TMU_CSR_BASE_ADDR + 0x0f4)
+/* [31:0] PHY2 in queue address (must be initialized with one of the
+ * xxx_INQ_PKTPTR cbus addresses)
+ */
+#define TMU_PHY2_INQ_ADDR	(TMU_CSR_BASE_ADDR + 0x0f8)
+/* [31:0] PHY3 in queue address (must be initialized with one of the
+ * xxx_INQ_PKTPTR cbus addresses)
+ */
+#define TMU_PHY3_INQ_ADDR	(TMU_CSR_BASE_ADDR + 0x0fc)
+#define TMU_BMU_INQ_ADDR	(TMU_CSR_BASE_ADDR + 0x100)
+#define TMU_TX_CTRL	(TMU_CSR_BASE_ADDR + 0x104)
+
+#define TMU_BUS_ACCESS_WDATA	(TMU_CSR_BASE_ADDR + 0x108)
+#define TMU_BUS_ACCESS	(TMU_CSR_BASE_ADDR + 0x10c)
+#define TMU_BUS_ACCESS_RDATA	(TMU_CSR_BASE_ADDR + 0x110)
+
+#define TMU_PE_SYS_CLK_RATIO	(TMU_CSR_BASE_ADDR + 0x114)
+#define TMU_PE_STATUS	(TMU_CSR_BASE_ADDR + 0x118)
+#define TMU_TEQ_MAX_THRESHOLD	(TMU_CSR_BASE_ADDR + 0x11c)
+/* [31:0] PHY4 in queue address (must be initialized with one of the
+ * xxx_INQ_PKTPTR cbus addresses)
+ */
+#define TMU_PHY4_INQ_ADDR	(TMU_CSR_BASE_ADDR + 0x134)
+/* [9:0] Scheduler Enable for each of the scheduler in the TDQ.
+ * This is a global Enable for all schedulers in PHY1
+ */
+#define TMU_TDQ1_SCH_CTRL	(TMU_CSR_BASE_ADDR + 0x138)
+/* [9:0] Scheduler Enable for each of the scheduler in the TDQ.
+ * This is a global Enable for all schedulers in PHY2
+ */
+#define TMU_TDQ2_SCH_CTRL	(TMU_CSR_BASE_ADDR + 0x13c)
+/* [9:0] Scheduler Enable for each of the scheduler in the TDQ.
+ * This is a global Enable for all schedulers in PHY3
+ */
+#define TMU_TDQ3_SCH_CTRL	(TMU_CSR_BASE_ADDR + 0x140)
+#define TMU_BMU_BUF_SIZE	(TMU_CSR_BASE_ADDR + 0x144)
+/* [31:0] PHY5 in queue address (must be initialized with one of the
+ * xxx_INQ_PKTPTR cbus addresses)
+ */
+#define TMU_PHY5_INQ_ADDR	(TMU_CSR_BASE_ADDR + 0x148)
+
+#define SW_RESET		BIT(0)	/* Global software reset */
+#define INQ_RESET		BIT(2)
+#define TEQ_RESET		BIT(3)
+#define TDQ_RESET		BIT(4)
+#define PE_RESET		BIT(5)
+#define MEM_INIT		BIT(6)
+#define MEM_INIT_DONE		BIT(7)
+#define LLM_INIT		BIT(8)
+#define LLM_INIT_DONE		BIT(9)
+#define ECC_MEM_INIT_DONE	BIT(10)
+
+struct tmu_cfg {
+	u32 pe_sys_clk_ratio;
+	unsigned long llm_base_addr;
+	u32 llm_queue_len;
+};
+
+/* Not HW related for pfe_ctrl / pfe common defines */
+#define DEFAULT_MAX_QDEPTH	80
+#define DEFAULT_Q0_QDEPTH	511 /*We keep one large queue for host tx qos */
+#define DEFAULT_TMU3_QDEPTH	127
+
+#endif /* _TMU_CSR_H_ */
diff --git a/drivers/net/pfe/base/cbus/util_csr.h b/drivers/net/pfe/base/cbus/util_csr.h
new file mode 100644
index 000000000..8b37b6fac
--- /dev/null
+++ b/drivers/net/pfe/base/cbus/util_csr.h
@@ -0,0 +1,47 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#ifndef _UTIL_CSR_H_
+#define _UTIL_CSR_H_
+
+#define UTIL_VERSION	(UTIL_CSR_BASE_ADDR + 0x000)
+#define UTIL_TX_CTRL	(UTIL_CSR_BASE_ADDR + 0x004)
+#define UTIL_INQ_PKTPTR	(UTIL_CSR_BASE_ADDR + 0x010)
+
+#define UTIL_HDR_SIZE	(UTIL_CSR_BASE_ADDR + 0x014)
+
+#define UTIL_PE0_QB_DM_ADDR0	(UTIL_CSR_BASE_ADDR + 0x020)
+#define UTIL_PE0_QB_DM_ADDR1	(UTIL_CSR_BASE_ADDR + 0x024)
+#define UTIL_PE0_RO_DM_ADDR0	(UTIL_CSR_BASE_ADDR + 0x060)
+#define UTIL_PE0_RO_DM_ADDR1	(UTIL_CSR_BASE_ADDR + 0x064)
+
+#define UTIL_MEM_ACCESS_ADDR	(UTIL_CSR_BASE_ADDR + 0x100)
+#define UTIL_MEM_ACCESS_WDATA	(UTIL_CSR_BASE_ADDR + 0x104)
+#define UTIL_MEM_ACCESS_RDATA	(UTIL_CSR_BASE_ADDR + 0x108)
+
+#define UTIL_TM_INQ_ADDR	(UTIL_CSR_BASE_ADDR + 0x114)
+#define UTIL_PE_STATUS	(UTIL_CSR_BASE_ADDR + 0x118)
+
+#define UTIL_PE_SYS_CLK_RATIO	(UTIL_CSR_BASE_ADDR + 0x200)
+#define UTIL_AFULL_THRES	(UTIL_CSR_BASE_ADDR + 0x204)
+#define UTIL_GAP_BETWEEN_READS	(UTIL_CSR_BASE_ADDR + 0x208)
+#define UTIL_MAX_BUF_CNT	(UTIL_CSR_BASE_ADDR + 0x20c)
+#define UTIL_TSQ_FIFO_THRES	(UTIL_CSR_BASE_ADDR + 0x210)
+#define UTIL_TSQ_MAX_CNT	(UTIL_CSR_BASE_ADDR + 0x214)
+#define UTIL_IRAM_DATA_0	(UTIL_CSR_BASE_ADDR + 0x218)
+#define UTIL_IRAM_DATA_1	(UTIL_CSR_BASE_ADDR + 0x21c)
+#define UTIL_IRAM_DATA_2	(UTIL_CSR_BASE_ADDR + 0x220)
+#define UTIL_IRAM_DATA_3	(UTIL_CSR_BASE_ADDR + 0x224)
+
+#define UTIL_BUS_ACCESS_ADDR	(UTIL_CSR_BASE_ADDR + 0x228)
+#define UTIL_BUS_ACCESS_WDATA	(UTIL_CSR_BASE_ADDR + 0x22c)
+#define UTIL_BUS_ACCESS_RDATA	(UTIL_CSR_BASE_ADDR + 0x230)
+
+#define UTIL_INQ_AFULL_THRES	(UTIL_CSR_BASE_ADDR + 0x234)
+
+struct util_cfg {
+	u32 pe_sys_clk_ratio;
+};
+
+#endif /* _UTIL_CSR_H_ */
diff --git a/drivers/net/pfe/base/pfe.h b/drivers/net/pfe/base/pfe.h
new file mode 100644
index 000000000..15b17802c
--- /dev/null
+++ b/drivers/net/pfe/base/pfe.h
@@ -0,0 +1,339 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#ifndef _PFE_H_
+#define _PFE_H_
+
+#include "cbus.h"
+
+/*
+ * WARNING: non atomic version.
+ */
+static inline void
+set_bit(unsigned long nr, void *addr)
+{
+	int *m = ((int *)addr) + (nr >> 5);
+	*m |= 1 << (nr & 31);
+}
+
+static inline int
+test_bit(int nr, const void *addr)
+{
+	return (1UL & (((const int *)addr)[nr >> 5] >> (nr & 31))) != 0UL;
+}
+
+/*
+ * WARNING: non atomic version.
+ */
+static inline void
+clear_bit(unsigned long nr, void *addr)
+{
+	int *m = ((int *)addr) + (nr >> 5);
+	*m &= ~(1 << (nr & 31));
+}
+
+/*
+ * WARNING: non atomic version.
+ */
+static inline int
+test_and_clear_bit(unsigned long nr, void *addr)
+{
+	unsigned long mask = 1 << (nr & 0x1f);
+	int *m = ((int *)addr) + (nr >> 5);
+	int old = *m;
+
+	*m = old & ~mask;
+	return (old & mask) != 0;
+}
+
+/*
+ * WARNING: non atomic version.
+ */
+static inline int
+test_and_set_bit(unsigned long nr, void *addr)
+{
+	unsigned long mask = 1 << (nr & 0x1f);
+	int *m = ((int *)addr) + (nr >> 5);
+	int old = *m;
+
+	*m = old | mask;
+	return (old & mask) != 0;
+}
+
+#ifndef BIT
+#define BIT(nr)                (1UL << (nr))
+#endif
+#define CLASS_DMEM_BASE_ADDR(i)	(0x00000000 | ((i) << 20))
+/*
+ * Only valid for mem access register interface
+ */
+#define CLASS_IMEM_BASE_ADDR(i)	(0x00000000 | ((i) << 20))
+#define CLASS_DMEM_SIZE	0x00002000
+#define CLASS_IMEM_SIZE	0x00008000
+
+#define TMU_DMEM_BASE_ADDR(i)	(0x00000000 + ((i) << 20))
+/*
+ * Only valid for mem access register interface
+ */
+#define TMU_IMEM_BASE_ADDR(i)	(0x00000000 + ((i) << 20))
+#define TMU_DMEM_SIZE	0x00000800
+#define TMU_IMEM_SIZE	0x00002000
+
+#define UTIL_DMEM_BASE_ADDR	0x00000000
+#define UTIL_DMEM_SIZE	0x00002000
+
+#define PE_LMEM_BASE_ADDR	0xc3010000
+#define PE_LMEM_SIZE	0x8000
+#define PE_LMEM_END	(PE_LMEM_BASE_ADDR + PE_LMEM_SIZE)
+
+#define DMEM_BASE_ADDR	0x00000000
+#define DMEM_SIZE	0x2000	/* TMU has less... */
+#define DMEM_END	(DMEM_BASE_ADDR + DMEM_SIZE)
+
+#define PMEM_BASE_ADDR	0x00010000
+#define PMEM_SIZE	0x8000	/* TMU has less... */
+#define PMEM_END	(PMEM_BASE_ADDR + PMEM_SIZE)
+
+#define writel(v, p) ({*(volatile unsigned int *)(p) = (v); })
+#define readl(p) (*(const volatile unsigned int *)(p))
+
+/* These check memory ranges from PE point of view/memory map */
+#define IS_DMEM(addr, len)				\
+	({ typeof(addr) addr_ = (addr);			\
+	((unsigned long)(addr_) >= DMEM_BASE_ADDR) &&	\
+	(((unsigned long)(addr_) + (len)) <= DMEM_END); })
+
+#define IS_PMEM(addr, len)				\
+	({ typeof(addr) addr_ = (addr);			\
+	((unsigned long)(addr_) >= PMEM_BASE_ADDR) &&	\
+	(((unsigned long)(addr_) + (len)) <= PMEM_END); })
+
+#define IS_PE_LMEM(addr, len)				\
+	({ typeof(addr) addr_ = (addr);			\
+	((unsigned long)(addr_) >=			\
+	PE_LMEM_BASE_ADDR) &&				\
+	(((unsigned long)(addr_) +			\
+	(len)) <= PE_LMEM_END); })
+
+#define IS_PFE_LMEM(addr, len)				\
+	({ typeof(addr) addr_ = (addr);			\
+	((unsigned long)(addr_) >=			\
+	CBUS_VIRT_TO_PFE(LMEM_BASE_ADDR)) &&		\
+	(((unsigned long)(addr_) + (len)) <=		\
+	CBUS_VIRT_TO_PFE(LMEM_END)); })
+
+#define __IS_PHYS_DDR(addr, len)			\
+	({ typeof(addr) addr_ = (addr);			\
+	((unsigned long)(addr_) >=			\
+	DDR_PHYS_BASE_ADDR) &&				\
+	(((unsigned long)(addr_) + (len)) <=		\
+	DDR_PHYS_END); })
+
+#define IS_PHYS_DDR(addr, len)	__IS_PHYS_DDR(DDR_PFE_TO_PHYS(addr), len)
+
+/*
+ * If using a run-time virtual address for the cbus base address use this code
+ */
+extern void *cbus_base_addr;
+extern void *ddr_base_addr;
+extern unsigned long ddr_phys_base_addr;
+extern unsigned int ddr_size;
+
+#define CBUS_BASE_ADDR	cbus_base_addr
+#define DDR_PHYS_BASE_ADDR	ddr_phys_base_addr
+#define DDR_BASE_ADDR	ddr_base_addr
+#define DDR_SIZE	ddr_size
+
+#define DDR_PHYS_END	(DDR_PHYS_BASE_ADDR + DDR_SIZE)
+
+#define LS1012A_PFE_RESET_WA	/*
+				 * PFE doesn't have global reset and re-init
+				 * should takecare few things to make PFE
+				 * functional after reset
+				 */
+#define PFE_CBUS_PHYS_BASE_ADDR	0xc0000000	/* CBUS physical base address
+						 * as seen by PE's.
+						 */
+/* CBUS physical base address as seen by PE's. */
+#define PFE_CBUS_PHYS_BASE_ADDR_FROM_PFE	0xc0000000
+
+#define DDR_PHYS_TO_PFE(p)	(((unsigned long)(p)) & 0x7FFFFFFF)
+#define DDR_PFE_TO_PHYS(p)	(((unsigned long)(p)) | 0x80000000)
+#define CBUS_PHYS_TO_PFE(p)	(((p) - PFE_CBUS_PHYS_BASE_ADDR) + \
+				PFE_CBUS_PHYS_BASE_ADDR_FROM_PFE)
+/* Translates to PFE address map */
+
+#define DDR_PHYS_TO_VIRT(p)	(((p) - DDR_PHYS_BASE_ADDR) + DDR_BASE_ADDR)
+#define DDR_VIRT_TO_PHYS(v)	(((v) - DDR_BASE_ADDR) + DDR_PHYS_BASE_ADDR)
+#define DDR_VIRT_TO_PFE(p)	(DDR_PHYS_TO_PFE(DDR_VIRT_TO_PHYS(p)))
+
+#define CBUS_VIRT_TO_PFE(v)	(((v) - CBUS_BASE_ADDR) + \
+				PFE_CBUS_PHYS_BASE_ADDR)
+#define CBUS_PFE_TO_VIRT(p)	(((unsigned long)(p) - \
+				PFE_CBUS_PHYS_BASE_ADDR) + CBUS_BASE_ADDR)
+
+/* The below part of the code is used in QOS control driver from host */
+#define TMU_APB_BASE_ADDR       0xc1000000      /* TMU base address seen by
+						 * pe's
+						 */
+
+enum {
+	CLASS0_ID = 0,
+	CLASS1_ID,
+	CLASS2_ID,
+	CLASS3_ID,
+	CLASS4_ID,
+	CLASS5_ID,
+	TMU0_ID,
+	TMU1_ID,
+	TMU2_ID,
+	TMU3_ID,
+#if !defined(CONFIG_FSL_PFE_UTIL_DISABLED)
+	UTIL_ID,
+#endif
+	MAX_PE
+};
+
+#define CLASS_MASK	(BIT(CLASS0_ID) | BIT(CLASS1_ID) |\
+			BIT(CLASS2_ID) | BIT(CLASS3_ID) |\
+			BIT(CLASS4_ID) | BIT(CLASS5_ID))
+#define CLASS_MAX_ID	CLASS5_ID
+
+#define TMU_MASK	(BIT(TMU0_ID) | BIT(TMU1_ID) |\
+			BIT(TMU3_ID))
+
+#define TMU_MAX_ID	TMU3_ID
+
+#if !defined(CONFIG_FSL_PFE_UTIL_DISABLED)
+#define UTIL_MASK	BIT(UTIL_ID)
+#endif
+
+struct pe_status {
+	u32	cpu_state;
+	u32	activity_counter;
+	u32	rx;
+	union {
+	u32	tx;
+	u32	tmu_qstatus;
+	};
+	u32	drop;
+#if defined(CFG_PE_DEBUG)
+	u32	debug_indicator;
+	u32	debug[16];
+#endif
+} __rte_aligned(16);
+
+struct pe_sync_mailbox {
+	u32 stop;
+	u32 stopped;
+};
+
+/* Drop counter definitions */
+
+#define	CLASS_NUM_DROP_COUNTERS	13
+#define	UTIL_NUM_DROP_COUNTERS	8
+
+/* PE information.
+ * Structure containing PE's specific information. It is used to create
+ * generic C functions common to all PE's.
+ * Before using the library functions this structure needs to be initialized
+ * with the different registers virtual addresses
+ * (according to the ARM MMU mmaping). The default initialization supports a
+ * virtual == physical mapping.
+ */
+struct pe_info {
+	u32 dmem_base_addr;	/* PE's dmem base address */
+	u32 pmem_base_addr;	/* PE's pmem base address */
+	u32 pmem_size;	/* PE's pmem size */
+
+	void *mem_access_wdata;	/* PE's _MEM_ACCESS_WDATA register
+				 * address
+				 */
+	void *mem_access_addr;	/* PE's _MEM_ACCESS_ADDR register
+				 * address
+				 */
+	void *mem_access_rdata;	/* PE's _MEM_ACCESS_RDATA register
+				 * address
+				 */
+};
+
+void pe_lmem_read(u32 *dst, u32 len, u32 offset);
+void pe_lmem_write(u32 *src, u32 len, u32 offset);
+
+void pe_dmem_memcpy_to32(int id, u32 dst, const void *src, unsigned int len);
+void pe_pmem_memcpy_to32(int id, u32 dst, const void *src, unsigned int len);
+
+u32 pe_pmem_read(int id, u32 addr, u8 size);
+
+void pe_dmem_write(int id, u32 val, u32 addr, u8 size);
+u32 pe_dmem_read(int id, u32 addr, u8 size);
+void class_pe_lmem_memcpy_to32(u32 dst, const void *src, unsigned int len);
+void class_pe_lmem_memset(u32 dst, int val, unsigned int len);
+void class_bus_write(u32 val, u32 addr, u8 size);
+u32 class_bus_read(u32 addr, u8 size);
+
+#define class_bus_readl(addr)	class_bus_read(addr, 4)
+#define class_bus_readw(addr)	class_bus_read(addr, 2)
+#define class_bus_readb(addr)	class_bus_read(addr, 1)
+
+#define class_bus_writel(val, addr)	class_bus_write(val, addr, 4)
+#define class_bus_writew(val, addr)	class_bus_write(val, addr, 2)
+#define class_bus_writeb(val, addr)	class_bus_write(val, addr, 1)
+
+#define pe_dmem_readl(id, addr)	pe_dmem_read(id, addr, 4)
+#define pe_dmem_readw(id, addr)	pe_dmem_read(id, addr, 2)
+#define pe_dmem_readb(id, addr)	pe_dmem_read(id, addr, 1)
+
+#define pe_dmem_writel(id, val, addr)	pe_dmem_write(id, val, addr, 4)
+#define pe_dmem_writew(id, val, addr)	pe_dmem_write(id, val, addr, 2)
+#define pe_dmem_writeb(id, val, addr)	pe_dmem_write(id, val, addr, 1)
+
+/*int pe_load_elf_section(int id, const void *data, elf32_shdr *shdr); */
+//int pe_load_elf_section(int id, const void *data, struct elf32_shdr *shdr,
+//			struct device *dev);
+
+void pfe_lib_init(void *cbus_base, void *ddr_base, unsigned long ddr_phys_base,
+		  unsigned int ddr_size);
+void bmu_init(void *base, struct BMU_CFG *cfg);
+void bmu_reset(void *base);
+void bmu_enable(void *base);
+void bmu_disable(void *base);
+void bmu_set_config(void *base, struct BMU_CFG *cfg);
+
+/*
+ * An enumerated type for loopback values.  This can be one of three values, no
+ * loopback -normal operation, local loopback with internal loopback module of
+ * MAC or PHY loopback which is through the external PHY.
+ */
+#ifndef __MAC_LOOP_ENUM__
+#define __MAC_LOOP_ENUM__
+enum mac_loop {LB_NONE, LB_EXT, LB_LOCAL};
+#endif
+
+/* Get Chip Revision level
+ *
+ */
+static inline unsigned int CHIP_REVISION(void)
+{
+	/*For LS1012A return always 1 */
+	return 1;
+}
+
+/* Start HIF rx DMA
+ *
+ */
+static inline void hif_rx_dma_start(void)
+{
+	writel(HIF_CTRL_DMA_EN | HIF_CTRL_BDP_CH_START_WSTB, HIF_RX_CTRL);
+}
+
+/* Start HIF tx DMA
+ *
+ */
+static inline void hif_tx_dma_start(void)
+{
+	writel(HIF_CTRL_DMA_EN | HIF_CTRL_BDP_CH_START_WSTB, HIF_TX_CTRL);
+}
+
+#endif /* _PFE_H_ */
