new file mode 100644
@@ -0,0 +1,1114 @@
+.. Copyright (c) <2021>, Intel Corporation
+ All rights reserved.
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions
+ are met:
+
+ - Redistributions of source code must retain the above copyright
+ notice, this list of conditions and the following disclaimer.
+
+ - Redistributions in binary form must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in
+ the documentation and/or other materials provided with the
+ distribution.
+
+ - Neither the name of Intel Corporation nor the names of its
+ contributors may be used to endorse or promote products derived
+ from this software without specific prior written permission.
+
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+ OF THE POSSIBILITY OF SUCH DAMAGE.
+
+==============
+eCPRI protocol
+==============
+eCPRI protocol is used for exchanging messages within ORAN 5G Front Haul.
+According to the ORAN FH specification the eCPRI packets are sent over Ethernet.
+They can be transmitted over standard Ethernet frames, or can use IP/UDP as the transport mechanism.
+In case of the IP/UDP transport mechanism the ORAN FH standard says that
+the UDP destination port used for eCPRI protocol is not fixed, thus, the user should be able to configure the port number dynamically.
+A change is required in DPDK APIs to allow it.
+And CVL rss and fdir rte_flow APIs are needed to support classfication of eCPRI protocol.
+this test plan contain 3 parts:
+*UDP dst port dynamically config for eCPRI
+*rss supporting for eCPRI
+*fdir supporting for eCPRI
+
+
+Prerequisites
+=============
+1. Hardware:
+ columbiaville_25g/columbiaville_100g
+
+2. Software:
+ dpdk: http://dpdk.org/git/dpdk
+ scapy: http://www.secdev.org/projects/scapy/
+
+3. Copy ice_wireless pkg to /lib/firmware/updates/intel/ice/ddp/ice.pkg
+
+4. load driver::
+
+ rmmod ice
+ insmod ice.ko
+
+5. Generate 4 VFs on PF0 and set mac address::
+
+ echo 4 > /sys/bus/pci/devices/0000:18:00.0/sriov_numvfs
+ ./usertools/dpdk-devbind.py -s
+ 0000:18:01.0 'Ethernet Adaptive Virtual Function 1889' if=enp24s1 drv=iavf unused=vfio-pci
+ 0000:18:01.1 'Ethernet Adaptive Virtual Function 1889' if=enp24s1f1 drv=iavf unused=vfio-pci
+ 0000:18:01.2 'Ethernet Adaptive Virtual Function 1889' if=enp24s1f2 drv=iavf unused=vfio-pci
+ 0000:18:01.3 'Ethernet Adaptive Virtual Function 1889' if=enp24s1f3 drv=iavf unused=vfio-pci
+
+ ip link set ens785f0 vf 0 mac 00:11:22:33:44:55
+ ip link set ens785f0 vf 1 mac 00:11:22:33:44:11
+ ip link set ens785f0 vf 2 mac 00:11:22:33:44:22
+ ip link set ens785f0 vf 3 mac 00:11:22:33:44:33
+
+6. Set VF0 as trust::
+
+ ip link set ens785f0 vf 0 trust on
+
+7. Bind 3 VFs to dpdk driver, keep one VF in kernel::
+
+ modprobe vfio-pci
+ ./usertools/dpdk-devbind.py -b vfio-pci 0000:18:01.0 0000:18:01.1 0000:18:01.2
+
+8. Launch dpdk on VF0, VF1 and VF2, and VF0 request DCF mode::
+
+ ./dpdk-testpmd -c 0xf -n 4 -a 0000:18:01.0,cap=dcf -a 0000:18:01.1 -a 0000:18:01.2 -- -i
+
+ testpmd> set fwd rxonly
+ testpmd> set verbose 1
+ testpmd> start
+ testpmd> show port info all
+
+ check the VF0 driver is net_ice_dcf.
+
+9. For test case 01 and test case 02, need to add print log in testpmd to show the eCPRI ptype, then compile DPDK again:
+
+diff --git a/drivers/net/iavf/iavf_rxtx.c b/drivers/net/iavf/iavf_rxtx.c
+ index af5a28d84..3dbd5ab97 100644
+ --- a/drivers/net/iavf/iavf_rxtx.c
+ +++ b/drivers/net/iavf/iavf_rxtx.c
+ @@ -1314,6 +1314,8 @@ iavf_recv_pkts_flex_rxd(void *rx_queue,
+ rxm->ol_flags = 0;
+ rxm->packet_type = ptype_tbl[IAVF_RX_FLEX_DESC_PTYPE_M &
+ rte_le_to_cpu_16(rxd.wb.ptype_flex_flags0)];
+ + printf("++++++++++++ptype=%u\n",
+ + IAVF_RX_FLEX_DESC_PTYPE_M & rte_le_to_cpu_16(rxd.wb.ptype_flex_flags0));
+ iavf_flex_rxd_to_vlan_tci(rxm, &rxd);
+ rxq->rxd_to_pkt_fields(rxq, rxm, &rxd);
+ pkt_flags = iavf_flex_rxd_error_to_pkt_flags(rx_stat_err0);
+ @@ -2346,7 +2348,7 @@ iavf_set_rx_function(struct rte_eth_dev *dev)
+ IAVF_DEV_PRIVATE_TO_ADAPTER(dev->data->dev_private);
+ struct iavf_info *vf = IAVF_DEV_PRIVATE_TO_VF(dev->data->dev_private);
+
+ -#ifdef RTE_ARCH_X86
+ +#if 0
+ struct iavf_rx_queue *rxq;
+ int i;
+ bool use_avx2 = false;
+ @@ -2446,6 +2448,7 @@ iavf_set_rx_function(struct rte_eth_dev *dev)
+ else
+ dev->rx_pkt_burst = iavf_recv_pkts;
+ }
+ + dev->rx_pkt_burst = iavf_recv_pkts_flex_rxd;
+ }
+
+ /* choose tx function*/
+ --
+
+
+Test case 01: add and delete eCPRI port config in DCF
+=====================================================
+1. add eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+2. send eCPRI pkts to VF1, check the pattern can be parsed correctly:
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE0(ptype=372)::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC0(ptype=373)::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x00')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC1(ptype=374)::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x01')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC3(ptype=375)::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x03')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC5(ptype=376)::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x05')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC6(ptype=377)::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x06')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC7(ptype=378)::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x07')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2(ptype=379)::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x08')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE5(ptype=380)::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x05')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI(ptype=381)::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x06')], iface="ens786f0")
+
+3. send eCPRI pkts which udp dport is not matched the config to VF1, check the pattern can not be recognized(all the ptype is 24)::
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE0::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5121)/Raw('\x10\x00')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC0::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5121)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x00')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC1::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5121)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x01')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC3::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5121)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x03')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC5::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5121)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x05')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC6::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5121)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x06')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC7::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5121)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x07')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5121)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x08')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE5::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5121)/Raw('\x10\x05')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5121)/Raw('\x10\x06')], iface="ens786f0")
+
+4. send same eCPRI pkts in step 2 to VF2, check the pattern can be parsed correctly.
+
+5. delete eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port rm ecpri 0x5123
+
+6. send same eCPRI pkts in step 2 to VF1, check the pattern can not be recognized(all the ptype is 24).
+
+
+Test case 02: test eCPRI port config when DCF exit and reset
+============================================================
+1. add eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+2. quit testpmd, then Launch testpmd again::
+
+ ./dpdk-testpmd -c 0xf -n 4 -a 0000:18:01.0,cap=dcf -a 0000:18:01.1 0000:18:01.2 -- -i
+ testpmd> set fwd rxonly
+ testpmd> set verbose 1
+ testpmd> start
+
+3. send eCPRI pkts which udp dport is match before config to VF1, check the pattern can not be recognized(all the ptype is 24)::
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE0::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC0::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x00')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC1::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x01')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC3::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x03')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC5::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x05')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC6::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x06')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2_SEC7::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x07')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE2::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x02')/Raw('x'*11)/Raw('\x08')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI_MSGTYPE5::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x05')], iface="ens786f0")
+
+MAC_IPV4_UDP_ECPRI::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x06')], iface="ens786f0")
+
+4. add eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+5. reset DCF by set mac address::
+
+ ip link set ens785f0 vf 0 mac 00:11:22:33:44:66
+
+6. send eCPRI pkts in step 3 to VF1, check the pattern can not be recognized(all the ptype is 24).
+
+7. quit testpmd, then Launch testpmd again, add eCPRI port config in DCF::
+
+ ./dpdk-testpmd -c 0xf -n 4 -a 0000:18:01.0,cap=dcf -a 0000:18:01.1 0000:18:01.2 -- -i
+ testpmd> set fwd rxonly
+ testpmd> set verbose 1
+ testpmd> start
+ testpmd> port config 0 udp_tunnel_port add ecpri 0x5123
+
+8. reset DCF by set trust off::
+
+ ip link set ens785f0 vf 0 trust off
+
+9. send eCPRI pkts in step 3 to VF1, check the pattern can not be recognized(all the ptype is 24).
+
+
+Test case 03: test DCF port config and linux port config
+========================================================
+1. add eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+2. add linux port config, check the cmd can not config succesfully::
+
+ ip link add vx0 type vxlan id 100 local 1.1.1.1 remote 2.2.2.2 dev ens785f0 dstport 0x1234
+ ifconfig vx0 up
+ ifconfig vx0 down
+
+ [1825286.116930] ice 0000:18:00.0: Cannot config tunnel, the capability is used by DCF
+
+3. delete eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port rm ecpri 0x5123
+
+4. add linux port config, check the cmd can config succesfully::
+
+ ifconfig vx0 up
+ ifconfig vx0 down
+
+5. quit testpmd, then Launch testpmd again::
+
+ ./dpdk-testpmd -c 0xf -n 4 -a 0000:18:01.0,cap=dcf -a 0000:18:01.1 -a 0000:18:01.2 -- -i
+ testpmd> set fwd rxonly
+ testpmd> set verbose 1
+ testpmd> start
+
+6. add linux port config::
+
+ ip link add vx0 type vxlan id 100 local 1.1.1.1 remote 2.2.2.2 dev ens785f0 dstport 0x1234
+ ifconfig vx0 up
+
+7. add eCPRI port config in DCF::
+
+ testpmd> port config 0 udp_tunnel_port add ecpri 0x5123
+ ice_dcf_send_aq_cmd(): No response (201 times) or return failure (desc: -63 / buff: -63)
+ udp tunneling port add error: (No such process)
+
+ check the cmd can not config succesfully.
+
+8. remove linux port config::
+
+ ifconfig vx0 down
+
+9. add eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+ check the cmd can config succesfully.
+
+
+Test case 04: negative eCPRI port config in DCF
+===============================================
+1. try below negative cmd in testpmd::
+
+ testpmd> port config 1 udp_tunnel_port add ecpri 0x5123
+ udp tunneling port add error: (Operation not supported)
+
+ testpmd> port config 5 udp_tunnel_port add ecpri 0x5123
+ Invalid port 5
+
+ testpmd> port config 15 udp_tunnel_port rm ecpri 0x5123
+ Invalid port 15
+
+ testpmd> port config a udp_tunnel_port add ecpri 0x5123
+ Bad arguments
+
+ testpmd> port config 0 udp_tunnel_port add ecpri 0
+ udp tunneling port add error: (Permission denied)
+
+ testpmd> port config 0 udp_tunnel_port rm ecpri 0
+ udp tunneling port add error: (Operation not permitted)
+
+ testpmd> port config 0 udp_tunnel_port add ecpri ffff
+ Bad arguments
+
+ testpmd> port config 0 udp_tunnel_port add ecpri 0xffff
+ udp tunneling port add error: (Permission denied)
+
+
+Test case 05: rss for udp ecpri
+===============================
+
+1. Add eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+2. Validate rule::
+
+ flow validate 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+
+3. Create rule and list rule::
+
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+
+4. Send a basic hit pattern packet, record the hash value,
+ check the packet is distributed to queues by RSS::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+
+5. Send hit pattern packets with changed input set in the rule,
+ check the received packets have different hash values with basic packet,
+ check the packets are distributed to queues by rss::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x47')], iface="ens786f0")
+
+6. Destroy the rule and list rule::
+
+ testpmd> flow destroy 1 rule 0
+ testpmd> flow list 1
+
+7. Send same packets with step 4 and 5,
+ check received packets don't have hash value or hash value is same, rule can't work.
+
+
+Test case 06: rss for eth_ecpri
+===============================
+
+1. Start testpmd without DCF mode::
+
+ dpdk-testpmd -c f -n 4 -a 18:01.1 -- -i --rxq=16 --txq=16
+
+2. Validate rule::
+
+ flow validate 1 ingress pattern eth / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+
+3. Create rule and list rule::
+
+ flow create 1 ingress pattern eth / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+
+4. Send a basic hit pattern packet, record the hash value,
+ check the packet is distributed to queues by RSS::
+
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+
+5. Send hit pattern packets with changed input set in the rule,
+ check the received packets have different hash values with basic packet,
+ check the packets are distributed to queues by rss::
+
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x47')], iface="ens786f0")
+
+6. Destroy the rule and list rule::
+
+ testpmd> flow destroy 1 rule 0
+ testpmd> flow list 1
+
+7. Send same packet with step 4,
+ check received packets don't have hash value or hash value is same, rule can't work.
+
+
+Test case 07: rss multirules + multiports
+=========================================
+
+1. Add eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+2. Create multi rules::
+
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+ flow create 1 ingress pattern eth / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+ flow create 2 ingress pattern eth / ipv4 / udp / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+ flow create 2 ingress pattern eth / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+
+3. Send a basic hit pattern packet, record the hash value,
+ check the packets are distributed to queues by RSS::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:22")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:22", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+
+4. Send hit pattern packets with changed input set in the rule,
+ check the received packets have different hash value with basic packet,
+ check the packets are distributed to queues by rss::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:22")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:22", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+
+5. Destroy the rule and list rule::
+
+ testpmd> flow destroy 1 rule 0
+ testpmd> flow list 1
+ testpmd> flow destroy 2 rule 0
+ testpmd> flow list 2
+
+6. Send same packet with step 3,
+ check received packets don't have hash value or hash value is same, rule can't work.
+
+
+Test case 08: rss without/with udp port set for udp ecpri rule
+==============================================================
+
+1. Create rule and list rule without udp port config::
+
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+
+2. Send basic hit pattern packets, record the hash value,
+ check parser is wrong, hash value is same,
+ RSS eCPRI UDP rule will return success, but not work::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x47')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x48')], iface="ens786f0")
+
+3. Add eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+4. Send basic hit pattern packets, check hash values are different.
+ check the packets are distributed to queues by RSS::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+
+
+Test case 09: DCF reset for udp ecpri rss
+=========================================
+
+1. Add eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+2. Create rule::
+
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+
+3. Send a basic hit pattern packet, record the hash value,
+ check the packet is distributed to queues by RSS::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+
+4. Send hit pattern packet with changed input set in the rule,
+ check the received packet has different hash value with basic packet,
+ check the packet is distributed to queues by rss::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+
+5. Reset DCF by set mac address::
+
+ ip link set ens785f0 vf 0 mac 00:11:22:33:44:11
+
+6. Send packets, check packets paser are wrong, check don't have or hash value is same::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x47')], iface="ens786f0")
+
+7. Reset DCF by set mac address::
+
+ ip link set ens785f0 vf 0 mac 00:11:22:33:44:55
+
+8. Quit testpmd and repeat step 1~6, get same result.
+
+8. Reset DCF by set trust off::
+
+ ip link set ens785f0 vf 0 trust off
+
+9. Repeat step 6, result is same.
+
+10. Set VF0 as trust::
+
+ ip link set ens785f0 vf 0 trust on
+
+
+Test case 10: DCF reset for eth ecpri rss
+=========================================
+
+1. Create rule::
+
+ flow create 1 ingress pattern eth / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+
+2. Send a basic hit pattern packet, record the hash value,
+ check the packet is distributed to queues by RSS::
+
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+
+3. Send hit pattern packet with changed input set in the rule,
+ check the received packet has different hash value with basic packet,
+ check the packet is distributed to queues by rss::
+
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+
+4. Reset DCF by set mac address::
+
+ ip link set ens785f0 vf 0 mac 00:11:22:33:44:11
+
+5. Send packets, check the received packets have different hash values, rule can work::
+
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x47')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x48')], iface="ens786f0")
+
+6. Reset DCF by set trust off::
+
+ ip link set ens785f0 vf 0 trust off
+
+7. Repeat step 1~5, result is same.
+
+8. Set VF0 as trust::
+
+ ip link set ens785f0 vf 0 trust on
+
+9. Reset DCF by set mac address::
+
+ ip link set ens785f0 vf 0 mac 00:11:22:33:44:55
+
+
+Test case 11: DCF exit for eth ecpri and udp ecpri rss
+======================================================
+
+1. Start testpmd with dcf mode on vf0::
+
+ ./dpdk-testpmd -c 0xff -n 6 -a 0000:18:01.0,cap=dcf --file-prefix=test1 -- -i
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+2. Start testpmd with iavf mode on vf1 and vf2::
+
+ ./dpdk-testpmd -c 0xff -n 6 -a 0000:60:01.1 -a 0000:60:01.2 --file-prefix=test2 -- -i --rxq=16 --txq=16
+ flow create 0 ingress pattern eth / ipv4 / udp / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+ flow create 1 ingress pattern eth / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+
+3. Send a basic hit pattern packet, record the hash value,
+ check the packets are distributed to queues by RSS::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:22", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+
+4. Send hit pattern packets with changed input set in the rule,
+ check the received packets have different hash values with basic packet,
+ check the packets are distributed to queues by rss::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:22", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+
+5. Quit dcf testpmd.
+
+6. Repeat 3 and 4 steps, check udp ecpri paser is wrong and rule can't work.
+ Check eth ecpri rule can work, has differnt hash values.
+
+
+Test case 12: eCPRI over Ethernet header pattern fdir
+=====================================================
+matched packets::
+
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+
+unmatched packets::
+
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+
+Enable RSS of eCPRI over Ethernet header in advance::
+
+ flow create 1 ingress pattern eth / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+
+Subcase 1: queue index
+----------------------
+
+1. validate fdir rule, and no rule listed::
+
+ flow validate 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions queue index 3 / mark id 1 / end
+
+2. create filter rules::
+
+ flow create 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions queue index 3 / mark id 1 / end
+
+3. send matched packets, check the packets are distributed to queue 3 with FDIR matched ID=0x1.
+ send unmatched packets, check the packets are distributed by RSS without FDIR matched ID.
+
+4. verify rules can be listed and destroyed::
+
+ testpmd> flow list 1
+
+ check the rule listed.
+ destroy the rule::
+
+ testpmd> flow destroy 1 rule 1
+
+5. verify matched packets are distributed by RSS without FDIR matched ID.
+ check there is no fdir rule listed.
+
+subcase 2: rss queues
+---------------------
+1. validate fdir rule, and no rule listed::
+
+ flow validate 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions rss queues 5 6 end / mark id 2 / end
+
+2. create fdir rule::
+
+ flow create 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions rss queues 5 6 end / mark id 2 / end
+
+3. send matched packets, check the packets are distributed to queue 5 or 6 with FDIR matched ID=0x2.
+ send unmatched packets, check the packets are distributed by RSS without FDIR matched ID.
+
+4. verify rules can be listed and destroyed::
+
+ testpmd> flow list 1
+
+ check the rule listed.
+ destroy the rule::
+
+ testpmd> flow destroy 1 rule 1
+
+5. verify matched packets are distributed by RSS without FDIR matched ID.
+ check there is no fdir rule listed.
+
+subcase 3: drop
+---------------
+1. validate fdir rule, and no rule listed::
+
+ flow validate 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions drop / end
+
+2. create fdir rule::
+
+ flow create 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions drop / end
+
+3. send matched packets, check the packets are dropped.
+ send unmatched packets, check the packets are distributed by RSS without FDIR matched ID.
+
+4. verify rules can be listed and destroyed::
+
+ testpmd> flow list 1
+
+ check the rule listed.
+ destroy the rule::
+
+ testpmd> flow destroy 1 rule 1
+
+5. verify matched packets are distributed by RSS without FDIR matched ID.
+ check there is no fdir rule listed.
+
+subcase 4: passthru
+-------------------
+1. validate fdir rule, and no rule listed::
+
+ flow validate 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions passthru / mark id 1 / end
+
+2. create fdir rule::
+
+ flow create 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions passthru / mark id 1 / end
+
+3. send matched packets, check the packets are distributed by RSS with FDIR matched ID=0x1.
+ send unmatched packets, check the packets are distributed by RSS without FDIR matched ID.
+
+4. verify rules can be listed and destroyed::
+
+ testpmd> flow list 1
+
+ check the rule listed.
+ destroy the rule::
+
+ testpmd> flow destroy 1 rule 1
+
+5. verify matched packets are distributed by RSS without FDIR matched ID.
+ check there is no fdir rule listed.
+
+subcase 5: mark + rss
+---------------------
+1. validate fdir rule, and no rule listed::
+
+ flow validate 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions mark / rss / end
+
+2. create fdir rule::
+
+ flow create 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions mark / rss / end
+
+3. send matched packets, check the packets are distributed by RSS with FDIR matched ID=0x0.
+ send unmatched packets, check the packets are distributed by RSS without FDIR matched ID.
+
+4. verify rules can be listed and destroyed::
+
+ testpmd> flow list 1
+
+ check the rule listed.
+ destroy the rule::
+
+ testpmd> flow destroy 1 rule 1
+
+5. verify matched packets are distributed by RSS without FDIR matched ID.
+ check there is no fdir rule listed.
+
+subcase 6: mark
+---------------
+1. validate fdir rule, and no rule listed::
+
+ flow validate 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions mark / end
+
+2. create fdir rule::
+
+ flow create 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions mark / end
+
+3. send matched packets, check the packets are distributed by RSS with FDIR matched ID=0x0.
+ send unmatched packets, check the packets are distributed by RSS without FDIR matched ID.
+
+4. verify rules can be listed and destroyed::
+
+ testpmd> flow list 1
+
+ check the rule listed.
+ destroy the rule::
+
+ testpmd> flow destroy 1 rule 1
+
+5. verify matched packets are distributed by RSS without FDIR matched ID.
+ check there is no fdir rule listed.
+
+
+Test case 13: eCPRI over IP/UDP header pattern fdir
+===================================================
+matched packets::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+
+unmatched packets::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+
+Add eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+Enable RSS of eCPRI over IP/UDP header in advance::
+
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+
+Subcase 1: queue index
+----------------------
+
+1. validate fdir rule, and no rule listed::
+
+ flow validate 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions queue index 2 / mark / end
+
+2. create filter rules::
+
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions queue index 2 / mark / end
+
+3. send matched packets, check the packets are distributed to queue 2 with FDIR matched ID=0x0.
+ send unmatched packets, check the packets are distributed by RSS without FDIR matched ID.
+
+4. verify rules can be listed and destroyed::
+
+ testpmd> flow list 1
+
+ check the rule listed.
+ destroy the rule::
+
+ testpmd> flow destroy 1 rule 1
+
+5. verify matched packets are distributed by RSS without FDIR matched ID.
+ check there is no fdir rule listed.
+
+subcase 2: rss queues
+---------------------
+1. validate fdir rule, and no rule listed::
+
+ flow validate 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions rss queues 5 6 end / mark id 2 / end
+
+2. create fdir rule::
+
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions rss queues 5 6 end / mark id 2 / end
+
+3. send matched packets, check the packets are distributed to queue 5 or 6 with FDIR matched ID=0x2.
+ send unmatched packets, check the packets are distributed by RSS without FDIR matched ID.
+
+4. verify rules can be listed and destroyed::
+
+ testpmd> flow list 1
+
+ check the rule listed.
+ destroy the rule::
+
+ testpmd> flow destroy 1 rule 1
+
+5. verify matched packets are distributed by RSS without FDIR matched ID.
+ check there is no fdir rule listed.
+
+subcase 3: drop
+---------------
+1. validate fdir rule, and no rule listed::
+
+ flow validate 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions drop / end
+
+2. create fdir rule::
+
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions drop / end
+
+3. send matched packets, check the packets are dropped.
+ send unmatched packets, check the packets are distributed by RSS without FDIR matched ID.
+
+4. verify rules can be listed and destroyed::
+
+ testpmd> flow list 1
+
+ check the rule listed.
+ destroy the rule::
+
+ testpmd> flow destroy 1 rule 1
+
+5. verify matched packets are distributed by RSS without FDIR matched ID.
+ check there is no fdir rule listed.
+
+subcase 4: passthru
+-------------------
+1. validate fdir rule, and no rule listed::
+
+ flow validate 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions passthru / mark id 1 / end
+
+2. create fdir rule::
+
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions passthru / mark id 1 / end
+
+3. send matched packets, check the packets are distributed by RSS with FDIR matched ID=0x1.
+ send unmatched packets, check the packets are distributed by RSS without FDIR matched ID.
+
+4. verify rules can be listed and destroyed::
+
+ testpmd> flow list 1
+
+ check the rule listed.
+ destroy the rule::
+
+ testpmd> flow destroy 1 rule 1
+
+5. verify matched packets are distributed by RSS without FDIR matched ID.
+ check there is no fdir rule listed.
+
+subcase 5: mark + rss
+---------------------
+1. validate fdir rule, and no rule listed::
+
+ flow validate 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions mark / rss / end
+
+2. create fdir rule::
+
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions mark / rss / end
+
+3. send matched packets, check the packets are distributed by RSS with FDIR matched ID=0x0.
+ send unmatched packets, check the packets are distributed by RSS without FDIR matched ID.
+
+4. verify rules can be listed and destroyed::
+
+ testpmd> flow list 1
+
+ check the rule listed.
+ destroy the rule::
+
+ testpmd> flow destroy 1 rule 1
+
+5. verify matched packets are distributed by RSS without FDIR matched ID.
+ check there is no fdir rule listed.
+
+subcase 6: mark
+---------------
+1. validate fdir rule, and no rule listed::
+
+ flow validate 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions mark / end
+
+2. create fdir rule::
+
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions mark / end
+
+3. send matched packets, check the packets are distributed by RSS with FDIR matched ID=0x0.
+ send unmatched packets, check the packets are distributed by RSS without FDIR matched ID.
+
+4. verify rules can be listed and destroyed::
+
+ testpmd> flow list 1
+
+ check the rule listed.
+ destroy the rule::
+
+ testpmd> flow destroy 1 rule 1
+
+5. verify matched packets are distributed by RSS without FDIR matched ID.
+ check there is no fdir rule listed.
+
+
+Test case 14: ecpri fdir multirules
+===================================
+Add eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+Enable RSS for eCPRI over MAC/UDP::
+
+ flow create 1 ingress pattern eth / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+ flow create 2 ingress pattern eth / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+ flow create 2 ingress pattern eth / ipv4 / udp / ecpri common type iq_data / end actions rss types ecpri end key_len 0 queues end / end
+
+1. create multi rules::
+
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions rss queues 5 6 end / mark id 0 / end
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2346 / end actions passthru / mark id 1 / end
+ flow create 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions drop / end
+ flow create 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2346 / end actions queue index 1 / mark id 2 / end
+ flow create 2 ingress pattern eth / ecpri common type iq_data pc_id is 0x2346 / end actions mark id 3 / end
+ flow create 2 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2346 / end actions mark / rss / end
+
+2. send matched packets and unmatched packets::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:22", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:22", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:22")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:22")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x46')], iface="ens786f0")
+
+3. check results:
+ pkt1 to queue 5 or 6 with mark id 0
+ pkt2 is distributed by rss with mark id 1
+ pkt3 drop
+ pkt4 to queue 1 with mark id 2
+ pkt5 is distributed by rss
+ pkt6 is distributed by rss with mark id 3
+ pkt7 is distributed by rss
+ pkt8 is distributed by rss with mark id 0
+
+
+Test case 15: ecpri fdir negative case
+======================================
+1. create ecpri over IP/UDP fdir rule without setting DCF eCPRI port::
+
+ testpmd> flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions rss queues 5 6 end / mark id 0 / end
+ iavf_fdir_add(): Failed to add rule request due to no hw resource
+ iavf_flow_create(): Failed to create flow
+ port_flow_complain(): Caught PMD error type 2 (flow rule (handle)): Failed to create parser engine.: Invalid argument
+
+2. check there is no rule listed.
+
+
+Test case 16: ecpri fdir when DCF reset
+=======================================
+1. add eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+ create two fdir rules::
+
+ flow create 1 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions queue index 1 / mark id 1 / end
+ flow create 1 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions queue index 2 / mark id 2 / end
+
+2. send packets::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+
+ check pkt1 is to queue 1 with mark id 1, pkt2 is to queue 2 with mark id 2
+
+3. reset DCF by set mac address::
+
+ ip link set enp59s0f0 vf 0 mac 00:11:22:33:44:11
+
+4. send same packets, check pkt1 is distributed by rss without mark id, pkt2 is to queue 2 with mark id 2
+
+5. quit testpmd and repeat step 1 and step 2, get same results.
+
+6. reset DCF by set trust off::
+
+ ip link set enp59s0f0 vf 0 trust off
+
+7. send same packets check pkt1 is distributed by rss without mark id, pkt2 is to queue 2 with mark id 2.
+
+
+Test case 17: ecpri fdir when DCF exit
+======================================
+1. start testpmd with dcf mode on vf0::
+
+ ./dpdk-testpmd -c 0xff -n 6 -a 0000:18:01.0,cap=dcf --file-prefix=vf0 -- -i
+
+ add eCPRI port config in DCF::
+
+ port config 0 udp_tunnel_port add ecpri 0x5123
+
+2. start testpmd with iavf mode on vf1 and vf2::
+
+ ./dpdk-testpmd -c 0xff00 -n 6 -a 0000:18:01.1 -a 0000:18:01.2 --file-prefix=vf1 -- -i --rxq=16 --txq=16
+
+ create two fdir rules::
+
+ flow create 0 ingress pattern eth / ipv4 / udp / ecpri common type iq_data pc_id is 0x2345 / end actions queue index 1 / mark id 1 / end
+ flow create 0 ingress pattern eth / ecpri common type iq_data pc_id is 0x2345 / end actions queue index 2 / mark id 2 / end
+
+3. send packets::
+
+ sendp([Ether(dst="00:11:22:33:44:11")/IP()/UDP(dport=0x5123)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+ sendp([Ether(dst="00:11:22:33:44:11", type=0xAEFE)/Raw('\x10\x00\x02\x24\x23\x45')], iface="ens786f0")
+
+ check pkt1 is to queue 1 with mark id 1, pkt2 is to queue 2 with mark id 2
+
+4. quit dcf testpmd, send same packets,
+ check pkt1 is distributed by rss without mark id, pkt2 is to queue 2 with mark id 2.