diff mbox series

[V1,1/3] test_plans: add ice_header_split_perf test plan

Message ID 20221226065514.10020-1-yingyax.han@intel.com (mailing list archive)
State Accepted
Headers
Series add ice_header_split_perf test suite |

Commit Message

Yingya Han Dec. 26, 2022, 6:55 a.m. UTC 
  Signed-off-by: Yingya Han <yingyax.han@intel.com>
---
 .../ice_header_split_perf_test_plan.rst       | 236 ++++++++++++++++++
 test_plans/index.rst                          |   1 +
 2 files changed, 237 insertions(+)
 create mode 100644 test_plans/ice_header_split_perf_test_plan.rst
diff mbox series

Patch

diff --git a/test_plans/ice_header_split_perf_test_plan.rst b/test_plans/ice_header_split_perf_test_plan.rst
new file mode 100644
index 00000000..da07a28b
--- /dev/null
+++ b/test_plans/ice_header_split_perf_test_plan.rst
@@ -0,0 +1,236 @@ 
+.. SPDX-License-Identifier: BSD-3-Clause
+   Copyright(c) 2022 Intel Corporation
+
+==============================================================
+Benchmark the performance of header split forwarding with E810
+==============================================================
+
+Description
+===========
+When Rx queue is configured with RTE_ETH_RX_OFFLOAD_BUFFER_SPLIT offload
+and corresponding protocol, packets received will be directly split into
+two different mempools.
+
+Prerequisites
+=============
+
+1. Hardware:
+
+   1.1) header split perf test for Intel® Ethernet Network Adapter E810-CQDA2:
+        1 NIC or 2 NIC cards attached to the same processor and 1 port used of each NIC.
+   1.2) header split perf test for Intel® Ethernet Network Adapter E810-XXVDA4:
+        1 NIC card attached to the processor and 4 ports used.
+
+2. Software::
+
+    dpdk: git clone http://dpdk.org/git/dpdk
+    trex: git clone http://trex-tgn.cisco.com/trex/release/v2.93.tar.gz
+
+
+Test Case
+=========
+The test case check the throughput result with ipv4, in the case,
+we will send the bi-direction flows with line rate, then we can check the 
+passthrough rate.
+
+Common Steps
+------------
+1. Bind tested ports to vfio-pci::
+
+    <dpdk_dir>#./usertools/dpdk-devbind.py -s
+    0000:17:00.0 'Device 1592' if=ens5f0 drv=ice unused=vfio-pci
+    0000:4b:00.0 'Device 1592' if=ens6f0 drv=ice unused=vfio-pci
+    <dpdk_dir>#./usertools/dpdk-devbind.py -b vfio-pci <pci device id>
+    <dpdk_dir>#./usertools/dpdk-devbind.py -b vfio-pci 0000:17:00.0
+    <dpdk_dir>#./usertools/dpdk-devbind.py -b vfio-pci 0000:4b:00.0
+
+2. Configure traffic generator to send traffic
+
+    Test flow MAC table.
+
+    +------+---------+------------+----------------+
+    | Flow | Traffic | MAC        | MAC            |
+    |      | Gen.    | Src.       | Dst.           |
+    |      | Port    | Address    | Address        |
+    +======+=========+============+================+
+    |   1  |   TG0   | Random MAC | 11:22:33:44:55 |
+    +------+---------+------------+----------------+
+    |   2  |   TG1   | Random Mac | 11:22:33:44:55 |
+    +------+---------+------------+----------------+
+    |   3  |   TG2   | Random Mac | 11:22:33:44:55 |
+    +------+---------+------------+----------------+
+    |   4  |   TG3   | Random Mac | 11:22:33:44:55 |
+    +------+---------+------------+----------------+
+
+    The Flow IP table.
+
+    +------+---------+------------+---------+
+    | Flow | Traffic | IPV4       | IPV4    |
+    |      | Gen.    | Src.       | Dest.   |
+    |      | Port    | Address    | Address |
+    +======+=========+============+=========+
+    |   1  |   TG0   | Any IP     | 2.1.1.1 |
+    +------+---------+------------+---------+
+    |   2  |   TG1   | Any IP     | 1.1.1.1 |
+    +------+---------+------------+---------+
+    |   3  |   TG2   | Any IP     | 4.1.1.1 |
+    +------+---------+------------+---------+
+    |   4  |   TG3   | Any IP     | 3.1.1.1 |
+    +------+---------+------------+---------+
+
+    Set the packet length : 64 bytes-1518 bytes
+    The IPV4 Dest Address increase with the num 1024.
+
+3. Test results table.
+
+    +-----------+------------+-------------+---------+
+    |  Fwd_core | Frame Size |  Throughput |   Rate  |
+    +===========+============+=============+=========+
+    |  1C/1T    |    64      |  xxxxx Mpps |   xxx % |
+    +-----------+------------+-------------+---------+
+    |  1C/1T    |   ...      |  xxxxx Mpps |   xxx % |
+    +-----------+------------+-------------+---------+
+    |  2C/2T    |    64      |  xxxxx Mpps |   xxx % |
+    +-----------+------------+-------------+---------+
+    |  2C/2T    |    ...     |  xxxxx Mpps |   xxx % |
+    +-----------+------------+-------------+---------+
+    |  4C/4T    |    64      |  xxxxx Mpps |   xxx % |
+    +-----------+------------+-------------+---------+
+    |  4C/4T    |    ...     |  xxxxx Mpps |   xxx % |
+    +-----------+------------+-------------+---------+
+    |  8C/8T    |    64      |  xxxxx Mpps |   xxx % |
+    +-----------+------------+-------------+---------+
+    |  8C/8T    |    ...     |  xxxxx Mpps |   xxx % |
+    +-----------+------------+-------------+---------+
+
+Test Case 1: test_perf_enable_header_split_rx_on
+------------------------------------------------
+
+1. Bind PF ports to dpdk driver as common step 1::
+
+    ./usertools/dpdk-devbind.py -b vfio-pci 17:00.0 4b:00.0
+
+2. Start dpdk-testpmd::
+
+     <build_dir>/app/dpdk-testpmd -l 5,6 -n 8 --force-max-simd-bitwidth=64 \
+     -- -i --portmask=0x3 --rxq=1 --txq=1 --txd=1024 --rxd=1024 --forward=rxonly \
+     --nb-cores=1 --mbuf-size=2048,2048
+
+    Note:
+      -force-max-simd-bitwidth: Set 64, the feature only support 64.
+      -mbuf-size=2048,2048: config two mempools.
+
+3. Config mac split::
+    
+    testpmd>port stop all
+    testpmd>port config 0 rx_offload buffer_split on
+    testpmd>port config 1 rx_offload buffer_split on
+    testpmd>set rxhdrs eth
+    testpmd>port start all
+    testpmd>start
+
+4. Configure traffic generator to send traffic as common step 2.
+
+5. Record Test results as common step 3.
+
+Test case 2: test_perf_disable_header_split_rx_on
+-------------------------------------------------
+
+1. Bind PF ports to dpdk driver as common step 1::
+
+    ./usertools/dpdk-devbind.py -b vfio-pci 17:00.0 4b:00.0
+
+2. Start dpdk-testpmd::
+
+     <build_dir>/app/dpdk-testpmd -l 5,6 -n 8 --force-max-simd-bitwidth=64 \
+     -- -i --portmask=0x3 --rxq=1 --txq=1 --txd=1024 --rxd=1024 --forward=rxonly \
+     --nb-cores=1
+
+     Note:
+      -force-max-simd-bitwidth: Set 64, the feature only support 64.
+
+3. Configure traffic generator to send traffic as common step 2.
+
+4. Record Test results as common step 3.
+
+5. Start dpdk-testpmd::
+
+     <build_dir>/app/dpdk-testpmd -l 5,6 -n 8 --force-max-simd-bitwidth=64 \
+     -- -i --portmask=0x3 --rxq=1 --txq=1 --txd=1024 --rxd=1024 --forward=rxonly \
+     --nb-cores=1 --mbuf-size=2048,2048
+
+     Note:
+      -force-max-simd-bitwidth: Set 64, the feature only support 64.
+      -mbuf-size=2048,2048: config two mempools.
+
+6. Configure traffic generator to send traffic as common step 2.
+
+7. Record Test results as common step 3.
+
+Test case 3: test_perf_enable_header_split
+------------------------------------------
+
+1. Bind PF ports to dpdk driver as common step 1::
+
+    ./usertools/dpdk-devbind.py -b vfio-pci 17:00.0 4b:00.0
+
+2. Start dpdk-testpmd::
+
+     <build_dir>/app/dpdk-testpmd -l 5,6 -n 8 --force-max-simd-bitwidth=64 \
+     -- -i --portmask=0x3 --rxq=1 --txq=1 --txd=1024 --rxd=1024 --forward=rxonly \
+     --nb-cores=1 --mbuf-size=2048,2048
+
+    Note:
+      -force-max-simd-bitwidth: Set 64, the feature only support 64.
+      -mbuf-size=2048,2048: config two mempools.
+
+3. Config udp split::
+    
+    testpmd>port stop all
+    testpmd>port config 0 rx_offload buffer_split on
+    testpmd>port config 1 rx_offload buffer_split on
+    testpmd>set rxhdrs inner-ipv4-udp
+    testpmd>port start all
+    testpmd>start
+    
+4. Config traffic generator as common step 2.
+   
+5. Record Test results as common step 3.
+
+6. Config traffic generator with udp flow.
+
+7. Record Test results as common step 3.
+
+Test case 4: test_perf_disable_header_split
+-------------------------------------------
+
+1. Bind PF ports to dpdk driver as common step 1::
+
+    ./usertools/dpdk-devbind.py -b vfio-pci 17:00.0 4b:00.0
+
+2. Start dpdk-testpmd::
+
+     <build_dir>/app/dpdk-testpmd -l 5,6 -n 8 --force-max-simd-bitwidth=64 \
+     -- -i --portmask=0x3 --rxq=1 --txq=1 --txd=1024 --rxd=1024 --forward=io \
+     --nb-cores=1
+
+    Note:
+      -force-max-simd-bitwidth: Set 64, the feature only support 64.
+
+3. Configure traffic generator to send traffic as common step 2.
+
+4. Record Test results as common step 3.
+
+5. Start dpdk-testpmd::
+
+     <build_dir>/app/dpdk-testpmd -l 5,6 -n 8 --force-max-simd-bitwidth=64 \
+     -- -i --portmask=0x3 --rxq=1 --txq=1 --txd=1024 --rxd=1024 --forward=io \
+     --nb-cores=1 --mbuf-size=2048,2048
+
+    Note:
+      -force-max-simd-bitwidth: Set 64, the feature only support 64.
+      -mbuf-size=2048,2048: config two mempools.
+
+6. Configure traffic generator to send traffic as common step 2.
+
+7. Record Test results as common step 3.
diff --git a/test_plans/index.rst b/test_plans/index.rst
index 9ca954e2..a4e7c7e8 100644
--- a/test_plans/index.rst
+++ b/test_plans/index.rst
@@ -35,6 +35,7 @@  The following are the test plans for the DPDK DTS automated test system.
     ice_dcf_switch_filter_pppoe_test_plan
     ice_dcf_switch_filter_gtpu_test_plan
     ice_dcf_flow_priority_test_plan
+    ice_header_split_perf_test_plan.rst
     ice_flow_priority_test_plan
     ice_dcf_qos_test_plan
     ice_enable_basic_hqos_on_pf_test_plan