[dpdk-dev,15/17] net/fm10k/base: improve re-map queues handle
Checks
Commit Message
Avoid potential FUM fault errors on a VF when updating MAC address
and VLAN information. Only use the register flow when the mailbox is
disconnected, by checking if the enqueue_tx returns
FM10K_MBX_ERR_NO_MBX. If the mailbox message can be sent, there is no
reason to bother with the register writes which are only intended to
be used during VF driver initialization.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
---
drivers/net/fm10k/base/fm10k_common.c | 3 +++
drivers/net/fm10k/base/fm10k_pf.c | 42 ++++++++++++++++++++++++-----------
2 files changed, 32 insertions(+), 13 deletions(-)
@@ -230,6 +230,9 @@ s32 fm10k_disable_queues_generic(struct fm10k_hw *hw, u16 q_cnt)
/* clear tx_ready to prevent any false hits for reset */
hw->mac.tx_ready = false;
+ if (FM10K_REMOVED(hw->hw_addr))
+ return FM10K_SUCCESS;
+
/* clear the enable bit for all rings */
for (i = 0; i < q_cnt; i++) {
reg = FM10K_READ_REG(hw, FM10K_TXDCTL(i));
@@ -926,9 +926,35 @@ STATIC s32 fm10k_iov_assign_default_mac_vlan_pf(struct fm10k_hw *hw,
fm10k_tlv_attr_put_mac_vlan(msg, FM10K_MAC_VLAN_MSG_DEFAULT_MAC,
vf_info->mac, vf_vid);
- /* load onto outgoing mailbox, ignore any errors on enqueue */
- if (vf_info->mbx.ops.enqueue_tx)
- vf_info->mbx.ops.enqueue_tx(hw, &vf_info->mbx, msg);
+ /* Configure Queue control register with new VLAN ID. The TXQCTL
+ * register is RO from the VF, so the PF must do this even in the
+ * case of notifying the VF of a new VID via the mailbox.
+ */
+ txqctl = ((u32)vf_vid << FM10K_TXQCTL_VID_SHIFT) &
+ FM10K_TXQCTL_VID_MASK;
+ txqctl |= (vf_idx << FM10K_TXQCTL_TC_SHIFT) |
+ FM10K_TXQCTL_VF | vf_idx;
+
+ for (i = 0; i < queues_per_pool; i++)
+ FM10K_WRITE_REG(hw, FM10K_TXQCTL(vf_q_idx + i), txqctl);
+
+ /* try loading a message onto outgoing mailbox first */
+ if (vf_info->mbx.ops.enqueue_tx) {
+ err = vf_info->mbx.ops.enqueue_tx(hw, &vf_info->mbx, msg);
+ if (err != FM10K_MBX_ERR_NO_MBX)
+ return err;
+ err = FM10K_SUCCESS;
+ }
+
+ /* If we aren't connected to a mailbox, this is most likely because
+ * the VF driver is not running. It should thus be safe to re-map
+ * queues and use the registers to pass the MAC address so that the VF
+ * driver gets correct information during its initialization.
+ */
+
+ /* MAP Tx queue back to 0 temporarily, and disable it */
+ FM10K_WRITE_REG(hw, FM10K_TQMAP(qmap_idx), 0);
+ FM10K_WRITE_REG(hw, FM10K_TXDCTL(vf_q_idx), 0);
/* verify ring has disabled before modifying base address registers */
txdctl = FM10K_READ_REG(hw, FM10K_TXDCTL(vf_q_idx));
@@ -967,16 +993,6 @@ STATIC s32 fm10k_iov_assign_default_mac_vlan_pf(struct fm10k_hw *hw,
FM10K_TDLEN_ITR_SCALE_SHIFT);
err_out:
- /* configure Queue control register */
- txqctl = ((u32)vf_vid << FM10K_TXQCTL_VID_SHIFT) &
- FM10K_TXQCTL_VID_MASK;
- txqctl |= (vf_idx << FM10K_TXQCTL_TC_SHIFT) |
- FM10K_TXQCTL_VF | vf_idx;
-
- /* assign VLAN ID */
- for (i = 0; i < queues_per_pool; i++)
- FM10K_WRITE_REG(hw, FM10K_TXQCTL(vf_q_idx + i), txqctl);
-
/* restore the queue back to VF ownership */
FM10K_WRITE_REG(hw, FM10K_TQMAP(qmap_idx), vf_q_idx);
return err;