[v1] net/virtio: wait device ready during reset
Checks
Commit Message
According to virtio spec, the device MUST reset when 0 is written to
device_status, and present 0 in device_status once reset is done.
This patch waits status value to be 0 during reset operation, if
timeout in 3 seconds, log and continue.
Signed-off-by: Xueming Li <xuemingl@nvidia.com>
Cc: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
---
drivers/net/virtio/virtio.c | 15 +++++++++++++--
1 file changed, 13 insertions(+), 2 deletions(-)
Comments
On 9/15/21 12:21 PM, Xueming Li wrote:
> According to virtio spec, the device MUST reset when 0 is written to
> device_status, and present 0 in device_status once reset is done.
>
> This patch waits status value to be 0 during reset operation, if
> timeout in 3 seconds, log and continue.
I have no strong opinion on timeout.
>
> Signed-off-by: Xueming Li <xuemingl@nvidia.com>
> Cc: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
> ---
> drivers/net/virtio/virtio.c | 15 +++++++++++++--
> 1 file changed, 13 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/net/virtio/virtio.c b/drivers/net/virtio/virtio.c
> index 7e1e77797f..f865b27b65 100644
> --- a/drivers/net/virtio/virtio.c
> +++ b/drivers/net/virtio/virtio.c
> @@ -3,7 +3,10 @@
> * Copyright(c) 2020 Red Hat, Inc.
> */
>
> +#include <unistd.h>
> +
> #include "virtio.h"
> +#include "virtio_logs.h"
>
> uint64_t
> virtio_negotiate_features(struct virtio_hw *hw, uint64_t host_features)
> @@ -38,9 +41,17 @@ virtio_write_dev_config(struct virtio_hw *hw, size_t offset,
> void
> virtio_reset(struct virtio_hw *hw)
> {
> + uint32_t retry = 0;
> +
> VIRTIO_OPS(hw)->set_status(hw, VIRTIO_CONFIG_STATUS_RESET);
> - /* flush status write */
> - VIRTIO_OPS(hw)->get_status(hw);
> + /* Flush status write and wait device ready max 3 seconds. */
> + while (VIRTIO_OPS(hw)->get_status(hw) != VIRTIO_CONFIG_STATUS_RESET) {
> + if (retry++ > 3000) {
> + PMD_INIT_LOG(WARNING, "device reset timeout");
I think it would be very useful to log ethdev port ID here.
> + break;
> + }
> + usleep(1000L);
> + }
> }
>
> void
>
On Wed, 2021-09-15 at 12:27 +0300, Andrew Rybchenko wrote:
> On 9/15/21 12:21 PM, Xueming Li wrote:
> > According to virtio spec, the device MUST reset when 0 is written to
> > device_status, and present 0 in device_status once reset is done.
> >
> > This patch waits status value to be 0 during reset operation, if
> > timeout in 3 seconds, log and continue.
>
> I have no strong opinion on timeout.
>
> >
> > Signed-off-by: Xueming Li <xuemingl@nvidia.com>
> > Cc: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
> > ---
> > drivers/net/virtio/virtio.c | 15 +++++++++++++--
> > 1 file changed, 13 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/net/virtio/virtio.c b/drivers/net/virtio/virtio.c
> > index 7e1e77797f..f865b27b65 100644
> > --- a/drivers/net/virtio/virtio.c
> > +++ b/drivers/net/virtio/virtio.c
> > @@ -3,7 +3,10 @@
> > * Copyright(c) 2020 Red Hat, Inc.
> > */
> >
> > +#include <unistd.h>
> > +
> > #include "virtio.h"
> > +#include "virtio_logs.h"
> >
> > uint64_t
> > virtio_negotiate_features(struct virtio_hw *hw, uint64_t host_features)
> > @@ -38,9 +41,17 @@ virtio_write_dev_config(struct virtio_hw *hw, size_t offset,
> > void
> > virtio_reset(struct virtio_hw *hw)
> > {
> > + uint32_t retry = 0;
> > +
> > VIRTIO_OPS(hw)->set_status(hw, VIRTIO_CONFIG_STATUS_RESET);
> > - /* flush status write */
> > - VIRTIO_OPS(hw)->get_status(hw);
> > + /* Flush status write and wait device ready max 3 seconds. */
> > + while (VIRTIO_OPS(hw)->get_status(hw) != VIRTIO_CONFIG_STATUS_RESET) {
> > + if (retry++ > 3000) {
> > + PMD_INIT_LOG(WARNING, "device reset timeout");
>
> I think it would be very useful to log ethdev port ID here.
Good suggesiton, v2 sent.
>
> > + break;
> > + }
> > + usleep(1000L);
> > + }
> > }
> >
> > void
> >
>
@@ -3,7 +3,10 @@
* Copyright(c) 2020 Red Hat, Inc.
*/
+#include <unistd.h>
+
#include "virtio.h"
+#include "virtio_logs.h"
uint64_t
virtio_negotiate_features(struct virtio_hw *hw, uint64_t host_features)
@@ -38,9 +41,17 @@ virtio_write_dev_config(struct virtio_hw *hw, size_t offset,
void
virtio_reset(struct virtio_hw *hw)
{
+ uint32_t retry = 0;
+
VIRTIO_OPS(hw)->set_status(hw, VIRTIO_CONFIG_STATUS_RESET);
- /* flush status write */
- VIRTIO_OPS(hw)->get_status(hw);
+ /* Flush status write and wait device ready max 3 seconds. */
+ while (VIRTIO_OPS(hw)->get_status(hw) != VIRTIO_CONFIG_STATUS_RESET) {
+ if (retry++ > 3000) {
+ PMD_INIT_LOG(WARNING, "device reset timeout");
+ break;
+ }
+ usleep(1000L);
+ }
}
void