Adds "--rxq-share=X" parameter to enable shared RxQ, share if device
supports, otherwise fallback to standard RxQ.
Share group number grows per X ports. X defaults to MAX, implies all
ports join share group 1.
Forwarding engine "shared-rxq" should be used which Rx only and update
stream statistics correctly.
Signed-off-by: Xueming Li <xuemingl@nvidia.com>
---
app/test-pmd/config.c | 6 +++++-
app/test-pmd/parameters.c | 13 +++++++++++++
app/test-pmd/testpmd.c | 12 ++++++++++++
app/test-pmd/testpmd.h | 2 ++
doc/guides/testpmd_app_ug/run_app.rst | 7 +++++++
5 files changed, 39 insertions(+), 1 deletion(-)
@@ -2709,7 +2709,11 @@ rxtx_config_display(void)
printf(" RX threshold registers: pthresh=%d hthresh=%d "
" wthresh=%d\n",
pthresh_tmp, hthresh_tmp, wthresh_tmp);
- printf(" RX Offloads=0x%"PRIx64"\n", offloads_tmp);
+ printf(" RX Offloads=0x%"PRIx64, offloads_tmp);
+ if (rx_conf->share_group > 0)
+ printf(" share group=%u",
+ rx_conf->share_group);
+ printf("\n");
}
/* per tx queue config only for first queue to be less verbose */
@@ -167,6 +167,7 @@ usage(char* progname)
printf(" --tx-ip=src,dst: IP addresses in Tx-only mode\n");
printf(" --tx-udp=src[,dst]: UDP ports in Tx-only mode\n");
printf(" --eth-link-speed: force link speed.\n");
+ printf(" --rxq-share: number of ports per shared rxq groups, defaults to MAX(1 group)\n");
printf(" --disable-link-check: disable check on link status when "
"starting/stopping ports.\n");
printf(" --disable-device-start: do not automatically start port\n");
@@ -607,6 +608,7 @@ launch_args_parse(int argc, char** argv)
{ "rxpkts", 1, 0, 0 },
{ "txpkts", 1, 0, 0 },
{ "txonly-multi-flow", 0, 0, 0 },
+ { "rxq-share", 2, 0, 0 },
{ "eth-link-speed", 1, 0, 0 },
{ "disable-link-check", 0, 0, 0 },
{ "disable-device-start", 0, 0, 0 },
@@ -1271,6 +1273,17 @@ launch_args_parse(int argc, char** argv)
}
if (!strcmp(lgopts[opt_idx].name, "txonly-multi-flow"))
txonly_multi_flow = 1;
+ if (!strcmp(lgopts[opt_idx].name, "rxq-share")) {
+ if (optarg == NULL) {
+ rxq_share = UINT32_MAX;
+ } else {
+ n = atoi(optarg);
+ if (n >= 0)
+ rxq_share = (uint32_t)n;
+ else
+ rte_exit(EXIT_FAILURE, "rxq-share must be >= 0\n");
+ }
+ }
if (!strcmp(lgopts[opt_idx].name, "no-flush-rx"))
no_flush_rx = 1;
if (!strcmp(lgopts[opt_idx].name, "eth-link-speed")) {
@@ -498,6 +498,11 @@ uint8_t record_core_cycles;
*/
uint8_t record_burst_stats;
+/*
+ * Number of ports per shared Rx queue group, 0 disable.
+ */
+uint32_t rxq_share;
+
unsigned int num_sockets = 0;
unsigned int socket_ids[RTE_MAX_NUMA_NODES];
@@ -3401,6 +3406,13 @@ rxtx_port_config(struct rte_port *port)
for (qid = 0; qid < nb_rxq; qid++) {
offloads = port->rx_conf[qid].offloads;
port->rx_conf[qid] = port->dev_info.default_rxconf;
+
+ if (rxq_share > 0 &&
+ (port->dev_info.dev_capa & RTE_ETH_DEV_CAPA_RXQ_SHARE))
+ /* Non-zero share group to enable RxQ share. */
+ port->rx_conf[qid].share_group = nb_ports / rxq_share
+ + 1;
+
if (offloads != 0)
port->rx_conf[qid].offloads = offloads;
@@ -477,6 +477,8 @@ extern enum tx_pkt_split tx_pkt_split;
extern uint8_t txonly_multi_flow;
+extern uint32_t rxq_share;
+
extern uint16_t nb_pkt_per_burst;
extern uint16_t nb_pkt_flowgen_clones;
extern int nb_flows_flowgen;
@@ -389,6 +389,13 @@ The command line options are:
Generate multiple flows in txonly mode.
+* ``--rxq-share=[X]``
+
+ Create queues in shared Rx queue mode if device supports.
+ Group number grows per X ports. X defaults to MAX, implies all ports
+ join share group 1. Forwarding engine "shared-rxq" should be used
+ which Rx only and update stream statistics correctly.
+
* ``--eth-link-speed``
Set a forced link speed to the ethernet port::