@@ -1,757 +1,979 @@
-.. Copyright (c) <2021>, Intel Corporation
- All rights reserved.
-
- Redistribution and use in source and binary forms, with or without
- modification, are permitted provided that the following conditions
- are met:
-
- - Redistributions of source code must retain the above copyright
- notice, this list of conditions and the following disclaimer.
-
- - Redistributions in binary form must reproduce the above copyright
- notice, this list of conditions and the following disclaimer in
- the documentation and/or other materials provided with the
- distribution.
-
- - Neither the name of Intel Corporation nor the names of its
- contributors may be used to endorse or promote products derived
- from this software without specific prior written permission.
-
- THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
- (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
- HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
- STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
- ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
- OF THE POSSIBILITY OF SUCH DAMAGE.
-
-===============================
-CVL Support Flow Priority in PF
-===============================
-
-Description
-===========
-In CVL PF rte_flow distribution mode(non-pipeline mode), a flow with priority = 1 will be programmed into switch filter,
-a flow with priority = 0 will be programmed into switch first then fdir.
-Currently only support priority 0 and 1. 1 means low priority and 0 means high priority.
-When looking up rule table, matched pkt will hit the high priority rule firstly,
-it will hit the low priority rule only when there is no high priority rule exist.
-
-
-Prerequisites
-=============
-
-Topology
---------
-1node/1nic/2port/fwd
-2node/1nic/1port/loopback
-
-Hardware
---------
-Supportted NICs: columbiaville_25g/columbiaville_100g
-
-Software
---------
-DPDK: http://dpdk.org/git/dpdk
-Scapy: http://www.secdev.org/projects/scapy/
-
-General Set Up
---------------
-1. Compile DPDK::
-
- # CC=gcc meson --werror -Denable_kmods=True -Dlibdir=lib --default-library=static <dpdk build dir>
- # ninja -C <dpdk build dir> -j 110
-
-2. Get the pci device id and interface of DUT and tester.
- For example, 0000:18:00.0 and 0000:18:00.1 is pci device id,
- ens785f0 and ens785f1 is interface::
-
- <dpdk dir># ./usertools/dpdk-devbind.py -s
-
- 0000:18:00.0 'Device 159b' if=ens785f0 drv=ice unused=vfio-pci
- 0000:18:00.1 'Device 159b' if=ens785f1 drv=ice unused=vfio-pci
-
-3. Bind the DUT port to dpdk::
-
- <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci <DUT port pci device id>
-
-4. Launch the userland ``testpmd`` application on DUT as follows and ::
-
- <dpdk build dir>/app/dpdk-testpmd <EAL options> -- -i --rxq=<queue number> --txq=<queue number>
- testpmd> set fwd rxonly
- testpmd> set verbose 1
- testpmd> rx_vxlan_port add 4789 0
- testpmd> start
-
-..note::
-
- For <EAL options>, you can use "-c 0xf -n 1", you can also refer to testpmd doc for other setings.
-
-
-Test Case
-=========
-
-Common Steps
-------------
-1. validate rules: two rules have same pattern, input set but different priority and actions.
-2. create rules and list rules.
-3. send matched packets, check the action hiting the rule with priority 0.
-4. send mismatched packets, check the packets will not hit any rules.
-5. destroy rule with priority 0, list rules.
-6. send matched packets, check the action hiting the rule with priority 1.
-7. send mismatched packets, check the packets will not hit any rules.
-8. recreate rules which priority is 0, list rule.
-9. destroy rule with priority 1, list rules.
-10. send matched packets, check the action hiting the rule with priority 0.
-11. send mismatched packets, check the packets will not hit any rules.
-12. destroy rule with priority 0, list rules.
-13. send matched packets, check the packets will not hit any rules.
-
-All the packets in this test plan use below settings:
-dst mac: 68:05:ca:8d:ed:a8
-dst mac change inputset: 68:05:ca:8d:ed:a3
-ipv4 src: 192.168.0.1
-ipv4 dst: 192.168.0.2
-ipv4 src change inputset: 192.168.0.3
-ipv4 dst change inputset: 192.168.0.4
-inner ipv4 src: 192.168.1.1
-inner ipv4 src change inputset: 192.168.1.2
-inner ipv4 dst: 192.168.1.3
-inner ipv4 dst change inputset: 192.168.1.4
-ipv6 src: CDCD:910A:2222:5498:8475:1111:3900:1536
-ipv6 dst: CDCD:910A:2222:5498:8475:1111:3900:2020
-ipv6 src change inputset: CDCD:910A:2222:5498:8475:1111:3900:1538
-ipv6 dst change inputset: CDCD:910A:2222:5498:8475:1111:3900:2028
-tos: 4
-tos change inputset: 5
-ttl: 2
-ttl change inputset: 9
-sport: 23
-sport change inputset: 33
-dport: 24
-dport change inputset: 34
-tc: 3
-tc change inputset: 7
-tni: 0x8
-tni change inputset: 0x1
-ethertype: 0x8863
-ethertype change inputset: 0x8864
-tci: 1
-tci change inputset: 2
-seid: 3
-seid change inputset: 4
-ipv4 proto_id: 0x0021
-ipv6 proto_id: 0x0057
-LCP proto_id: 0xc021
-IPCP proto_id: 0x8021
-
-Support Pattern and Input Set
------------------------------
-.. table::
-
- +---------------------+-------------------------------+-------------------------------------------+
- | Packet Types | Pattern | input set (non-pipeline mode) |
- +=====================+===============================+===========================================+
- | | MAC_IPV4_FRAG | N/A |
- | +-------------------------------+-------------------------------------------+
- | | MAC_IPV4_PAY | [Source IP], [Dest IP],[TOS],[TTL] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_IPV4_UDP_PAY | [Source IP], [Dest IP],[TOS],[TTL], |
- | +-------------------------------+-------------------------------------------+
- | IPv4/IPv6 + TCP/UDP | MAC_IPV4_TCP | [Source IP], [Dest IP],[TOS],[TTL], |
- | +-------------------------------+-------------------------------------------+
- | | MAC_IPV6 | [Source IP], [Dest IP] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_IPV6_UDP_PAY | [Source IP], [Dest IP],[TOS],[TTL], |
- | +-------------------------------+-------------------------------------------+
- | | MAC_IPV6_TCP | [Source IP], [Dest IP],[TOS],[TTL], |
- +---------------------+-------------------------------+-------------------------------------------+
- | | MAC_IPV4_TUN_IPV4_FRAG | [Out Dest IP], [VNI/GRE_KEY], |
- | | | [Inner Source IP], [Inner Dest IP] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_IPV4_TUN_IPV4_PAY | [Out Dest IP], [VNI/GRE_KEY], |
- | | | [Inner Source IP], [Inner Dest IP] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_IPV4_TUN_IPV4_UDP_PAY | [Out Dest IP], [VNI/GRE_KEY], |
- | | | [Inner Source IP], [Inner Dest IP], |
- | | | [Inner Source Port], [Inner Dest Port] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_IPV4_TUN_IPV4_TCP | [Out Dest IP], [VNI/GRE_KEY], |
- | | | [Inner Source IP], [Inner Dest IP], |
- | | | [Inner Source Port], [Inner Dest Port] |
- | tunnel +-------------------------------+-------------------------------------------+
- | | MAC_IPV4_TUN_MAC_IPV4_FRAG | [Out Dest IP], [VNI/GRE_KEY], |
- | | | [Inner Dest MAC], |
- | | | [Inner Source IP], [Inner Dest IP] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_IPV4_TUN_MAC_IPV4_PAY | [Out Dest IP], [VNI/GRE_KEY], |
- | | | [Inner Dest MAC], |
- | | | [Inner Source IP], [Inner Dest IP] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_IPV4_TUN_MAC_IPV4_UDP_PAY | [Out Dest IP], [VNI/GRE_KEY], |
- | | | [Inner Dest MAC], |
- | | | [Inner Source IP],[Inner Dest IP], |
- | | | [Inner Source Port], [Inner Dest Port] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_IPV4_TUN_MAC_IPV4_TCP | [Out Dest IP], [VNI/GRE_KEY], |
- | | | [Inner Dest MAC], |
- | | | [Inner Source IP], [Inner Dest IP], |
- | | | [Inner Source Port], [Inner Dest Port] |
- +---------------------+-------------------------------+-------------------------------------------+
- | ethertype filter | ethertype filter_PPPOED | [Ether type] |
- +---------------------+-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_IPV4_PAY | [Dest MAC], [VLAN], [seid], |
- | | _session_id_proto_id | [pppoe_proto_id] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_IPV6_PAY | [Dest MAC], [VLAN], [seid], |
- | | _session_id_proto_id | [pppoe_proto_id] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_IPV4_PAY_session_id | [Dest MAC], [seid], [pppoe_proto_id] |
- | | _proto_id | |
- | +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_IPV6_PAY_session_id | [Dest MAC], [seid], [pppoe_proto_id] |
- | | _proto_id | |
- | +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_IPV4_PAY_IP_address | [Source IP], [Dest IP] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_IPV4_UDP_PAY | [Source IP], [Dest IP], |
- | | | [Source Port], [Dest Port] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_IPV4_UDP_PAY | [Source IP], [Dest IP] |
- | | _non_src_dst_port | |
- | +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_IPV4_TCP_PAY | [Source IP], [Dest IP], |
- | | | [Source Port], [Dest Port] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_IPV4_TCP_PAY | [Source IP], [Dest IP] |
- | | _non_src_dst_port | |
- | +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_IPV6_PAY_IP_address | [Source IP], [Dest IP] |
- | PPPOES +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_IPV6_UDP_PAY | [Source IP], [Dest IP], |
- | | | [Source Port], [Dest Port] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_IPV6_UDP_PAY | [Source IP], [Dest IP] |
- | | _non_src_dst_port | |
- | +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_IPV6_TCP_PAY | [Source IP], [Dest IP], |
- | | | [Source Port], [Dest Port] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_IPV6_TCP_PAY | [Source IP], [Dest IP], |
- | | _non_src_dst_port | |
- | +-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_IPV4_PAY | [VLAN], [Source IP], [Dest IP] |
- | | _IP_address | |
- | +-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_IPV4_UDP_PAY | [VLAN], [Source IP], [Dest IP] |
- | | | [Source Port], [Dest Port] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_IPV4_UDP_PAY | [VLAN], [Source IP], [Dest IP] |
- | | _non_src_dst_port | |
- | +-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_IPV4_TCP_PAY | [VLAN], [Source IP], [Dest IP] |
- | | | [Source Port], [Dest Port] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_IPV4_TCP_PAY | [VLAN], [Source IP], [Dest IP] |
- | | _non_src_dst_port | |
- | +-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_IPV6_PAY | [VLAN], [Source IP], [Dest IP] |
- | | _IP_address | |
- | +-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_IPV6_UDP_PAY | [VLAN], [Source IP], [Dest IP] |
- | | | [Source Port], [Dest Port] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_IPV6_UDP_PAY | [VLAN], [Source IP], [Dest IP] |
- | | _non_src_dst_port | |
- | +-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_IPV6_TCP_PAY | [VLAN], [Source IP], [Dest IP] |
- | | | [Source Port], [Dest Port] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_IPV6_TCP_PAY | [VLAN], [Source IP], [Dest IP] |
- | | _non_src_dst_port | |
- | +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_LCP_PAY | [Dest MAC], [seid], [pppoe_proto_id] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_PPPOE_IPCP_PAY | [Dest MAC], [seid], [pppoe_proto_id] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_LCP_PAY | [Dest MAC], [VLAN], [seid], |
- | | | [pppoe_proto_id] |
- | +-------------------------------+-------------------------------------------+
- | | MAC_VLAN_PPPOE_IPCP_PAY | [Dest MAC], [VLAN], [seid], |
- | | | [pppoe_proto_id] |
- +---------------------+-------------------------------+-------------------------------------------+
-
-..note::
-
- the basic switch function of supported pattern is covered by cvl_switch_filter_test_plan.rst and cvl_switch_filter_pppoe_test_plan.rst.
- this test plan is designed to check the flow priority in switch, so we only select some patterns not all matrix in test plan.
-
-
-Test Case 1: MAC_IPV4_PAY
--------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> ttl is <ttl> / end actions queue index 1 / end
- testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> ttl is <ttl> / end actions queue index 4 / end
-
-matched packets::
-
- >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>,ttl=<ttl>)/("X"*480)], iface="<tester interface>")
-
-mismatched packets::
-
- >>> sendp([Ether(dst="<dst mac change inputset>")/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>,ttl=<ttl>)/("X"*480)], iface="<tester interface>")
- >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src change inputset>",dst="<ipv4 dst>",tos=<tos>,ttl=<ttl>)/("X"*480)], iface="<tester interface>")
- >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst change inputset>",tos=<tos>,ttl=<ttl>)/("X"*480)], iface="<tester interface>")
- >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos change inputset>,ttl=<ttl>)/("X"*480)], iface="<tester interface>")
- >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>,ttl=<ttl change inputset>)/("X"*480)], iface="<tester interface>")
-
-
-Test Case 2: MAC_IPV4_UDP_PAY
------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> / udp src is <sport> dst is <dport> / end actions rss queues 4 5 end / end
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> / udp src is <sport> dst is <dport> / end actions queue index 2 / end
-
-matched packets::
-
- >>> sendp([Ether()/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>)/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether()/IP(src="<ipv4 src change inputset>",dst="<ipv4 dst>",tos=<tos>)/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>")
- >>> sendp([Ether()/IP(src="<ipv4 src>",dst="<ipv4 dst change inputset>",tos=<tos>)/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>")
- >>> sendp([Ether()/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos change inputset>)/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>")
- >>> sendp([Ether()/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>)/UDP(sport=<sport change inputset>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>")
- >>> sendp([Ether()/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>)/UDP(sport=<sport>,dport=<dport change inputset>)/Raw("x"*80)],iface="<tester interface>")
-
-
-Test Case 3: MAC_IPV6_PAY
--------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv6 src is <ipv6 src> dst is <ipv6 dst> / end actions rss queues 4 5 end / end
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv6 src is <ipv6 src> dst is <ipv6 dst> / end actions queue index 8 / end
-
-matched packets::
-
- >>> sendp([Ether()/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/("X"*480)], iface="<tester interface>")
- >>> sendp([Ether()/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/IPv6ExtHdrFragment()/("X"*480)], iface="<tester interface>")
-
-mismatched packets::
-
- >>> sendp([Ether()/IPv6(src="<ipv6 src change inputset>", dst="<ipv6 dst>")/("X"*480)], iface="<tester interface>")
- >>> sendp([Ether()/IPv6(src="<ipv6 src>", dst="<ipv6 dst change inputset>")/("X"*480)], iface="<tester interface>")
- >>> sendp([Ether()/IPv6(src="<ipv6 src change inputset>", dst="<ipv6 dst>")/IPv6ExtHdrFragment()/("X"*480)], iface="<tester interface>")
- >>> sendp([Ether()/IPv6(src="<ipv6 src>", dst="<ipv6 dst change inputset>")/IPv6ExtHdrFragment()/("X"*480)], iface="<tester interface>")
-
-
-Test Case 4: MAC_IPV6_TCP
--------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv6 dst is <ipv6 dst> tc is <tc> / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / end
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv6 dst is <ipv6 dst> tc is <tc> / tcp src is <sport> dst is <dport> / end actions queue index 3 / end
-
-matched packets::
-
- >>> sendp([Ether()/IPv6(src="<ipv6 src>",dst="<ipv6 dst>",tc=<tc>)/TCP(sport=<sport>,dport=23)/Raw("x"*80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether()/IPv6(src="<ipv6 src>",dst="<ipv6 dst change inputset>",tc=<tc>)/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IPv6(src="<ipv6 src>",dst="<ipv6 dst>",tc=<tc change inputset>)/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IPv6(src="<ipv6 src>",dst="<ipv6 dst>",tc=<tc>)/TCP(sport=<sport change inputset>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IPv6(src="<ipv6 src>",dst="<ipv6 dst>",tc=<tc>)/TCP(sport=<sport>,dport=<dport change inputset>)/Raw("x"*80)],iface="<tester interface>",count=1)
-
-
-Test Case 5: MAC_IPV4_VXLAN_IPV4_FRAG
--------------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions rss queues 2 3 end / end
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 5 / end
-
-matched packets::
-
- >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>",frag=5)/Raw("x"*80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src change inputset>", dst="<ipv4 dst>",frag=5)/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst change inputset>",frag=5)/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>",frag=5)/Raw("x"*80)],iface="<tester interface>",count=1)
-
-
-Test Case 6: MAC_IPV4_VXLAN_IPV4_PAY
-------------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 5 / end
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions rss queues 2 3 end / end
-
-matched packets::
-
- >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>")/TCP()/Raw("x"*80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src change inputset>", dst="<ipv4 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst change inputset>")/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src change inputset>", dst="<ipv4 dst>")/TCP()/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst change inputset>")/TCP()/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>")/TCP()/Raw("x"*80)],iface="<tester interface>",count=1)
-
-
-Test Case 7: MAC_IPV4_NVGRE_MAC_IPV4_UDP_PAY
---------------------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 dst is <ipv4 dst> / nvgre tni is <tni> / eth dst is <dst mac> / ipv4 src is <inner ipv4 src> dst is <inner ipv4 dst> / udp src is <sport> dst is <dport> / end actions rss queues 2 3 end / end
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 dst is <ipv4 dst> / nvgre tni is <tni> / eth dst is <dst mac> / ipv4 src is <inner ipv4 src> dst is <inner ipv4 dst> / udp src is <sport> dst is <dport> / end actions queue index 4 / end
-
-matched packets::
-
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
-
-mismatched packets::
-
- >>> sendp([Ether()/IP(dst="<ipv4 dst change inputset>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni change inputset>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac change inputset>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src change inputset>", dst="<inner ipv4 dst>")/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst change inputset>")/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/UDP(sport=<sport change inputset>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/UDP(sport=<sport>,dport=<dport change inputset>)/Raw("x"*80)], iface="<tester interface>", count=1)
-
-
-Test Case 8: MAC_IPV4_NVGRE_MAC_IPV4_TCP
-----------------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 dst is <ipv4 dst> / nvgre tni is <tni> / eth dst is <dst mac> / ipv4 src is <inner ipv4 src> dst is <inner ipv4 dst> / tcp src is <sport> dst is <dport> / end actions queue index 5 / end
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 dst is <ipv4 dst> / nvgre tni is <tni> / eth dst is <dst mac> / ipv4 src is <inner ipv4 src> dst is <inner ipv4 dst> / tcp src is <sport> dst is <dport> / end actions rss queues 2 3 end / end
-
-matched packets::
-
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether()/IP(dst="<ipv4 dst change inputset>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni change inputset>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac change inputset>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src change inputset>", dst="<inner ipv4 dst>")/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst change inputset>")/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/TCP(sport=<sport change inputset>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>2", dst="<inner ipv4 dst>")/TCP(sport=<sport>,dport=<dport change inputset>)/Raw("x"*80)],iface="<tester interface>",count=1)
-
-
-Test Case 9: ethertype filter_PPPOED
-------------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth type is <ethertype> / end actions queue index 4 / end
- testpmd> flow create 0 priority 1 ingress pattern eth type is <ethertype> / end actions queue index 2 / end
-
-matched packets::
-
- >>> sendp([Ether(dst="<dst mac>", type=<ethertype>)/Raw("x" *80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>")/PPPoED()/Raw("x" *80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether(dst="<dst mac>", type=<ethertype change inputset>)/Raw("x" *80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>")/PPPoE()/Raw("x" *80)],iface="<tester interface>",count=1)
-
-
-Test Case 10: MAC_VLAN_PPPOE_IPV4_PAY_session_id_proto_id
----------------------------------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv4 proto_id> / end actions queue index 1 / end
- testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv4 proto_id> / end actions queue index 2 / end
-
-matched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<proto_id>)/IP()/Raw("x"*80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci change inputset>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid change inputset>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6()/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-
-Test Case 11: MAC_VLAN_PPPOE_IPV6_PAY_session_id_proto_id
----------------------------------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv6 proto_id> / end actions queue index 1 / end
- testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv6 proto_id> / end actions queue index 2 / end
-
-matched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6()/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci change inputset>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid change inputset>)/PPP(proto=<ipv6 proto_id>)/IPv6()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-
-Test Case 12: MAC_PPPOE_IPV4_PAY_IP_address
--------------------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / pppoes / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 1 / end
- testpmd> flow create 0 priority 1 ingress pattern eth / pppoes / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 2 / end
-
-matched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=3)/PPP(proto=0x0021)/IP(src="<ipv4 src>", dst="<ipv4 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=3)/PPP(proto=0x0021)/IP(src="<ipv4 src change inputset>", dst="<ipv4 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=3)/PPP(proto=0x0021)/IP(src="<ipv4 src>", dst="<ipv4 dst change inputset>")/Raw("x"*80)],iface="<tester interface>",count=1)
-
-
-Test Case 13: MAC_PPPOE_IPV6_UDP_PAY
-------------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / pppoes / ipv6 dst is <ipv6 dst> / udp src is <sport> dst is <dport> / end actions queue index 1 / end
- testpmd> flow create 0 priority 1 ingress pattern eth / pppoes / ipv6 dst is <ipv6 dst> / udp src is <sport> dst is <dport> / end actions queue index 2 / end
-
-matched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/UDP(sport=<sport>,dport=<dport>)/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src>", dst="<ipv6 dst change inputset>")/UDP(sport=<sport>,dport=<dport>)/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/UDP(sport=<sport change inputset>,dport=<dport>)/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/UDP(sport=<sport>,dport=<dport change inputset>)/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-
-Test Case 14: MAC_VLAN_PPPOE_IPV4_TCP_PAY_non_src_dst_port
-----------------------------------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / vlan tci is <tci> / pppoes / ipv4 src is <ipv4 src> dst is <ipv4 dst> / tcp / end actions queue index 1 / end
- testpmd> flow create 0 priority 1 ingress pattern eth / vlan tci is <tci> / pppoes / ipv4 src is <ipv4 src> dst is <ipv4 dst> / tcp / end actions queue index 2 / end
-
-matched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP(src="<ipv4 src>", dst="<ipv4 dst>")/TCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci change inputset>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP(src="<ipv4 src>", dst="<ipv4 dst>")/TCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP(src="<ipv4 src change inputset>", dst="<ipv4 dst>")/TCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP(src="<ipv4 src>", dst="<ipv4 dst change inputset>")/TCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP(src="<ipv4 src>", dst="<ipv4 dst>")/UDP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP(src="<ipv4 src>", dst="<ipv4 dst>")/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-
-Test Case 15: MAC_VLAN_PPPOE_IPV6_PAY_IP_address
-------------------------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / vlan tci is <tci> / pppoes / ipv6 src is <ipv6 src> / end actions queue index 1 / end
- testpmd> flow create 0 priority 1 ingress pattern eth / vlan tci is <tci> / pppoes / ipv6 src is <ipv6 src> / end actions queue index 2 / end
-
-matched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci change inputset>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src change inputset>", dst="<ipv6 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
-
-
-Test Case 16: MAC_PPPOE_LCP_PAY
--------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / pppoes seid is <seid> / pppoe_proto_id is <LCP proto_id> / end actions queue index 1 / end
- testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / pppoes seid is <seid> / pppoe_proto_id is <LCP proto_id> / end actions queue index 2 / end
-
-matched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid change inputset>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-
-Test Case 17: MAC_PPPOE_IPCP_PAY
---------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / pppoes seid is <seid> / pppoe_proto_id is <IPCP proto_id> / end actions queue index 1 / end
- testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / pppoes seid is <seid> / pppoe_proto_id is <IPCP proto_id> / end actions queue index 2 / end
-
-matched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid change inputset>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-
-Test Case 18: MAC_VLAN_PPPOE_LCP_PAY
-------------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <LCP proto_id> / end actions queue index 1 / end
- testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <LCP proto_id> / end actions queue index 2 / end
-
-matched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci change inputset>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid change inputset>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-
-Test Case 19: MAC_VLAN_PPPOE_IPCP_PAY
--------------------------------------
-rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <IPCP proto_id> / end actions queue index 1 / end
- testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <IPCP proto_id> / end actions queue index 2 / end
-
-matched packets::
-
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-mismatched packets::
-
- >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci change inputset>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid change inputset>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
- >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
-
-
-Test Case 20: check flow priority filter
-----------------------------------------
-1. launch testpmd with --log-level="ice,8"
-
-2. create rules with priority 0, check the rule is created to switch with a log "Succeeded to create (2) flow"::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 dst is <ipv4 src> / nvgre tni is <tni> / eth / ipv4 src is <inner ipv4 src> dst is <inner ipv4 dst> / end actions queue index 3 / end
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / end
- testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv6 proto_id> / end actions drop / end
-
-3. create rules with priority 0, and the action is mark, check the rule is created to fdir with a log "Succeeded to create (1) flow"::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / mark id 3 / end
-
-4. create rules with priority 1, check the rule is created to switch with a log "Succeeded to create (2) flow"::
-
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / end
- testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv6 proto_id> / end actions drop / end
-
-5. create rules with priority 1, and the action is mark, check the rule create fail::
-
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 dst is <ipv4 src> / nvgre tni is <tni> / eth / ipv4 src is <inner ipv4 src> dst is <inner ipv4 dst> / end actions queue index 3 / mark id 3 / end
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / mark id 3 / end
- testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv6 proto_id> / end actions drop / mark id 3 / end
-
-
-Test Case 21: negative test cases
----------------------------------
-1. create rules, check all these rules can not be created::
-
- testpmd> flow create 0 priority 2 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 3 / end
- testpmd> flow create 0 priority a ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 3 / end
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions mark / rss / end
-
-
-Test Case 22: exclusive test cases
-----------------------------------
-Subcase 1: same pattern/input set/action different priority
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-1. create same pattern, input set and action but different priority, check these two rules can be created::
-
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 3 / end
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 3 / end
-
-2. send matched pkts and check queue 3 receive this pkt::
-
- >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/TCP()/("X"*480)], iface="<tester interface>", count=1)
-
-3. destroy rules::
-
- flow flush 0
-
-Subcase 2: same pattern/input set/priority different action
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-1. create same pattern, input set and priority but different action, check the second rule can not be created::
-
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 3 / end
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions rss queues 4 5 end / end
-
-Subcase 3: some rules overlap
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-1. create rules::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / vlan / vlan / pppoes / pppoe_proto_id is 0x21 / end actions queue index 3 / end
- testpmd> flow create 0 priority 1 ingress pattern eth / vlan / vlan / pppoes seid is 1 / ipv4 / end actions queue index 2 / end
- testpmd> flow create 0 priority 1 ingress pattern eth / vlan / vlan tci is 12 / end actions queue index 4 / end
- testpmd> flow create 0 priority 0 ingress pattern eth dst is 00:00:00:01:03:13 / vlan / vlan / end actions rss queues 1 2 end / end
- testpmd> flow create 0 priority 0 ingress pattern eth dst is 00:00:00:01:03:03 / end actions queue index 8 / end
- testpmd> flow create 0 priority 1 ingress pattern eth / vlan tci is 1 / vlan tci is 2 / end actions queue index 4 / end
-
-2. check all the rules exist in the list::
-
- flow list 0
-
-3. send pkt which match rule 0 and rule 1, check the pkt can be received by queue 3::
-
- >>> sendp([Ether(type=0x8100)/Dot1Q(vlan=1,type=0x8100)/Dot1Q(vlan=0x2,type=0x8864)/PPPoE(sessionid=0x1)/PPP(proto=0x21)/IP()/UDP(dport=23)/("X"*480)], iface="<tester interface>")
-
-4. destroy rule 0, repeat step 3 and check the pkt can be received by queue 2::
-
- flow destroy 0 rule 0
-
-5. send pkt which match rule 2 and rule 3, check the pkt can be received by queue 1 or 2::
-
- >>> sendp([Ether(dst="00:00:00:01:03:13")/Dot1Q(vlan=1)/Dot1Q(vlan=12)/Raw("x"*480)], iface="<tester interface>", count=1)
-
-6. destroy rule 3, repeat step 5 and check the pkt can be received by queue 4::
-
- flow destroy 0 rule 3
-
-7. send pkt which match rule 4 and rule 5, check the pkt will be received by queue 8::
-
- >>> sendp([Ether(dst="00:00:00:01:03:03")/Dot1Q(vlan=1)/Dot1Q(vlan=2)/Raw("x"*480)], iface="<tester interface>", count=1)
-
-8. destroy rule 4, repeat step 7 and check the pkts can be received by queue 4::
-
- flow destroy 0 rule 3
+.. Copyright (c) <2021>, Intel Corporation
+ All rights reserved.
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions
+ are met:
+
+ - Redistributions of source code must retain the above copyright
+ notice, this list of conditions and the following disclaimer.
+
+ - Redistributions in binary form must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in
+ the documentation and/or other materials provided with the
+ distribution.
+
+ - Neither the name of Intel Corporation nor the names of its
+ contributors may be used to endorse or promote products derived
+ from this software without specific prior written permission.
+
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+ OF THE POSSIBILITY OF SUCH DAMAGE.
+
+===============================
+CVL Support Flow Priority in PF
+===============================
+
+Description
+===========
+In CVL PF rte_flow distribution mode(non-pipeline mode), a flow with priority = 1 will be programmed into switch filter,
+a flow with priority = 0 will be programmed into switch first then fdir.
+Currently only support priority 0 and 1. 1 means low priority and 0 means high priority.
+When looking up rule table, matched packets will hit the high priority rule firstly,
+it will hit the low priority rule only when there is no high priority rule exist.
+
+In CVL PF pipeline mode, a flow with priority = 1 will be programmed into fdir filter,
+a flow with priority = 0 will be programmed into switch filter. Rules are not prioritized.
+When looking up rule table, will look up switch filter first then fdir.
+
+Prerequisites
+=============
+
+Hardware
+--------
+Supportted NICs: columbiaville_25g/columbiaville_100g
+
+Software
+--------
+DPDK: http://dpdk.org/git/dpdk
+Scapy: http://www.secdev.org/projects/scapy/
+
+General Set Up
+--------------
+1. Compile DPDK::
+
+ # CC=gcc meson --werror -Denable_kmods=True -Dlibdir=lib --default-library=static <dpdk build dir>
+ # ninja -C <dpdk build dir> -j 110
+
+2. Get the pci device id and interface of DUT and tester.
+ For example, 0000:18:00.0 and 0000:18:00.1 is pci device id,
+ ens785f0 and ens785f1 is interface::
+
+ <dpdk dir># ./usertools/dpdk-devbind.py -s
+
+ 0000:18:00.0 'Device 159b' if=ens785f0 drv=ice unused=vfio-pci
+ 0000:18:00.1 'Device 159b' if=ens785f1 drv=ice unused=vfio-pci
+
+3. Bind the DUT port to dpdk::
+
+ <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci <DUT port pci device id>
+
+4. Launch the userland ``testpmd`` application on DUT as follows and ::
+
+ <dpdk build dir>/app/dpdk-testpmd <EAL options> -- -i --rxq=<queue number> --txq=<queue number>
+ testpmd> set fwd rxonly
+ testpmd> set verbose 1
+ testpmd> rx_vxlan_port add 4789 0
+ testpmd> start
+
+..note::
+
+ For <EAL options>, you can use "-c 0xf -n 1", you can also refer to testpmd doc for other setings.
+
+
+Test Case
+=========
+
+Common Steps
+------------
+Test Case 1 - 19 using below steps to check the matched packets will hit the high priority rule firstly,
+and hit the low priority rule only when there is no high priority rule exist:
+
+1. validate rules: two rules have same pattern, input set but different priority and actions.
+2. create rules and list rules.
+3. send matched packets, check the action hiting the rule with priority 0.
+4. send mismatched packets, check the packets will not hit any rules.
+5. destroy rule with priority 0, list rules.
+6. send matched packets, check the action hiting the rule with priority 1.
+7. send mismatched packets, check the packets will not hit any rules.
+8. recreate rules which priority is 0, list rule.
+9. destroy rule with priority 1, list rules.
+10. send matched packets, check the action hiting the rule with priority 0.
+11. send mismatched packets, check the packets will not hit any rules.
+12. destroy rule with priority 0, list rules.
+13. send matched packets, check the packets will not hit any rules.
+
+All the packets in this test plan use below settings:
+dst mac: 68:05:ca:8d:ed:a8
+dst mac change inputset: 68:05:ca:8d:ed:a3
+ipv4 src: 192.168.0.1
+ipv4 dst: 192.168.0.2
+ipv4 src change inputset: 192.168.0.3
+ipv4 dst change inputset: 192.168.0.4
+inner ipv4 src: 192.168.1.1
+inner ipv4 src change inputset: 192.168.1.2
+inner ipv4 dst: 192.168.1.3
+inner ipv4 dst change inputset: 192.168.1.4
+ipv6 src: CDCD:910A:2222:5498:8475:1111:3900:1536
+ipv6 dst: CDCD:910A:2222:5498:8475:1111:3900:2020
+ipv6 src change inputset: CDCD:910A:2222:5498:8475:1111:3900:1538
+ipv6 dst change inputset: CDCD:910A:2222:5498:8475:1111:3900:2028
+tos: 4
+tos change inputset: 5
+ttl: 2
+ttl change inputset: 9
+sport: 23
+sport change inputset: 33
+dport: 24
+dport change inputset: 34
+tc: 3
+tc change inputset: 7
+tni: 0x8
+tni change inputset: 0x1
+ethertype: 0x8863
+ethertype change inputset: 0x8864
+tci: 1
+tci change inputset: 2
+seid: 3
+seid change inputset: 4
+ipv4 proto_id: 0x0021
+ipv6 proto_id: 0x0057
+LCP proto_id: 0xc021
+IPCP proto_id: 0x8021
+
+Support Pattern and Input Set in Non-pipeline Mode
+--------------------------------------------------
+.. table::
+
+ +---------------------+-------------------------------+-------------------------------------------+
+ | Packet Types | Pattern | input set (non-pipeline mode) |
+ +=====================+===============================+===========================================+
+ | | MAC_IPV4_FRAG | N/A |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_IPV4_PAY | [Source IP], [Dest IP],[TOS],[TTL] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_IPV4_UDP_PAY | [Source IP], [Dest IP],[TOS],[TTL], |
+ | +-------------------------------+-------------------------------------------+
+ | IPv4/IPv6 + TCP/UDP | MAC_IPV4_TCP | [Source IP], [Dest IP],[TOS],[TTL], |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_IPV6 | [Source IP], [Dest IP] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_IPV6_UDP_PAY | [Source IP], [Dest IP],[TOS],[TTL], |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_IPV6_TCP | [Source IP], [Dest IP],[TOS],[TTL], |
+ +---------------------+-------------------------------+-------------------------------------------+
+ | | MAC_IPV4_TUN_IPV4_FRAG | [Out Dest IP], [VNI/GRE_KEY], |
+ | | | [Inner Source IP], [Inner Dest IP] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_IPV4_TUN_IPV4_PAY | [Out Dest IP], [VNI/GRE_KEY], |
+ | | | [Inner Source IP], [Inner Dest IP] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_IPV4_TUN_IPV4_UDP_PAY | [Out Dest IP], [VNI/GRE_KEY], |
+ | | | [Inner Source IP], [Inner Dest IP], |
+ | | | [Inner Source Port], [Inner Dest Port] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_IPV4_TUN_IPV4_TCP | [Out Dest IP], [VNI/GRE_KEY], |
+ | | | [Inner Source IP], [Inner Dest IP], |
+ | | | [Inner Source Port], [Inner Dest Port] |
+ | tunnel +-------------------------------+-------------------------------------------+
+ | | MAC_IPV4_TUN_MAC_IPV4_FRAG | [Out Dest IP], [VNI/GRE_KEY], |
+ | | | [Inner Dest MAC], |
+ | | | [Inner Source IP], [Inner Dest IP] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_IPV4_TUN_MAC_IPV4_PAY | [Out Dest IP], [VNI/GRE_KEY], |
+ | | | [Inner Dest MAC], |
+ | | | [Inner Source IP], [Inner Dest IP] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_IPV4_TUN_MAC_IPV4_UDP_PAY | [Out Dest IP], [VNI/GRE_KEY], |
+ | | | [Inner Dest MAC], |
+ | | | [Inner Source IP],[Inner Dest IP], |
+ | | | [Inner Source Port], [Inner Dest Port] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_IPV4_TUN_MAC_IPV4_TCP | [Out Dest IP], [VNI/GRE_KEY], |
+ | | | [Inner Dest MAC], |
+ | | | [Inner Source IP], [Inner Dest IP], |
+ | | | [Inner Source Port], [Inner Dest Port] |
+ +---------------------+-------------------------------+-------------------------------------------+
+ | ethertype filter | ethertype filter_PPPOED | [Ether type] |
+ +---------------------+-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_IPV4_PAY | [Dest MAC], [VLAN], [seid], |
+ | | _session_id_proto_id | [pppoe_proto_id] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_IPV6_PAY | [Dest MAC], [VLAN], [seid], |
+ | | _session_id_proto_id | [pppoe_proto_id] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_IPV4_PAY_session_id | [Dest MAC], [seid], [pppoe_proto_id] |
+ | | _proto_id | |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_IPV6_PAY_session_id | [Dest MAC], [seid], [pppoe_proto_id] |
+ | | _proto_id | |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_IPV4_PAY_IP_address | [Source IP], [Dest IP] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_IPV4_UDP_PAY | [Source IP], [Dest IP], |
+ | | | [Source Port], [Dest Port] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_IPV4_UDP_PAY | [Source IP], [Dest IP] |
+ | | _non_src_dst_port | |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_IPV4_TCP_PAY | [Source IP], [Dest IP], |
+ | | | [Source Port], [Dest Port] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_IPV4_TCP_PAY | [Source IP], [Dest IP] |
+ | | _non_src_dst_port | |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_IPV6_PAY_IP_address | [Source IP], [Dest IP] |
+ | PPPOES +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_IPV6_UDP_PAY | [Source IP], [Dest IP], |
+ | | | [Source Port], [Dest Port] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_IPV6_UDP_PAY | [Source IP], [Dest IP] |
+ | | _non_src_dst_port | |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_IPV6_TCP_PAY | [Source IP], [Dest IP], |
+ | | | [Source Port], [Dest Port] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_IPV6_TCP_PAY | [Source IP], [Dest IP], |
+ | | _non_src_dst_port | |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_IPV4_PAY | [VLAN], [Source IP], [Dest IP] |
+ | | _IP_address | |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_IPV4_UDP_PAY | [VLAN], [Source IP], [Dest IP] |
+ | | | [Source Port], [Dest Port] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_IPV4_UDP_PAY | [VLAN], [Source IP], [Dest IP] |
+ | | _non_src_dst_port | |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_IPV4_TCP_PAY | [VLAN], [Source IP], [Dest IP] |
+ | | | [Source Port], [Dest Port] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_IPV4_TCP_PAY | [VLAN], [Source IP], [Dest IP] |
+ | | _non_src_dst_port | |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_IPV6_PAY | [VLAN], [Source IP], [Dest IP] |
+ | | _IP_address | |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_IPV6_UDP_PAY | [VLAN], [Source IP], [Dest IP] |
+ | | | [Source Port], [Dest Port] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_IPV6_UDP_PAY | [VLAN], [Source IP], [Dest IP] |
+ | | _non_src_dst_port | |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_IPV6_TCP_PAY | [VLAN], [Source IP], [Dest IP] |
+ | | | [Source Port], [Dest Port] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_IPV6_TCP_PAY | [VLAN], [Source IP], [Dest IP] |
+ | | _non_src_dst_port | |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_LCP_PAY | [Dest MAC], [seid], [pppoe_proto_id] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_PPPOE_IPCP_PAY | [Dest MAC], [seid], [pppoe_proto_id] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_LCP_PAY | [Dest MAC], [VLAN], [seid], |
+ | | | [pppoe_proto_id] |
+ | +-------------------------------+-------------------------------------------+
+ | | MAC_VLAN_PPPOE_IPCP_PAY | [Dest MAC], [VLAN], [seid], |
+ | | | [pppoe_proto_id] |
+ +---------------------+-------------------------------+-------------------------------------------+
+
+..note::
+
+ the basic switch function of supported pattern is covered by cvl_switch_filter_test_plan.rst and cvl_switch_filter_pppoe_test_plan.rst.
+ this test plan is designed to check the flow priority in switch, so we only select some patterns not all matrix in test plan.
+
+
+Test Case 1: MAC_IPV4_PAY
+-------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> ttl is <ttl> / end actions queue index 1 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> ttl is <ttl> / end actions queue index 4 / end
+
+matched packets::
+
+ >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>,ttl=<ttl>)/("X"*480)], iface="<tester interface>")
+
+mismatched packets::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>")/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>,ttl=<ttl>)/("X"*480)], iface="<tester interface>")
+ >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src change inputset>",dst="<ipv4 dst>",tos=<tos>,ttl=<ttl>)/("X"*480)], iface="<tester interface>")
+ >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst change inputset>",tos=<tos>,ttl=<ttl>)/("X"*480)], iface="<tester interface>")
+ >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos change inputset>,ttl=<ttl>)/("X"*480)], iface="<tester interface>")
+ >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>,ttl=<ttl change inputset>)/("X"*480)], iface="<tester interface>")
+
+
+Test Case 2: MAC_IPV4_UDP_PAY
+-----------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> / udp src is <sport> dst is <dport> / end actions rss queues 4 5 end / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> / udp src is <sport> dst is <dport> / end actions queue index 2 / end
+
+matched packets::
+
+ >>> sendp([Ether()/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>)/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether()/IP(src="<ipv4 src change inputset>",dst="<ipv4 dst>",tos=<tos>)/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>")
+ >>> sendp([Ether()/IP(src="<ipv4 src>",dst="<ipv4 dst change inputset>",tos=<tos>)/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>")
+ >>> sendp([Ether()/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos change inputset>)/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>")
+ >>> sendp([Ether()/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>)/UDP(sport=<sport change inputset>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>")
+ >>> sendp([Ether()/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>)/UDP(sport=<sport>,dport=<dport change inputset>)/Raw("x"*80)],iface="<tester interface>")
+
+
+Test Case 3: MAC_IPV6_PAY
+-------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv6 src is <ipv6 src> dst is <ipv6 dst> / end actions rss queues 4 5 end / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv6 src is <ipv6 src> dst is <ipv6 dst> / end actions queue index 8 / end
+
+matched packets::
+
+ >>> sendp([Ether()/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/("X"*480)], iface="<tester interface>")
+ >>> sendp([Ether()/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/IPv6ExtHdrFragment()/("X"*480)], iface="<tester interface>")
+
+mismatched packets::
+
+ >>> sendp([Ether()/IPv6(src="<ipv6 src change inputset>", dst="<ipv6 dst>")/("X"*480)], iface="<tester interface>")
+ >>> sendp([Ether()/IPv6(src="<ipv6 src>", dst="<ipv6 dst change inputset>")/("X"*480)], iface="<tester interface>")
+ >>> sendp([Ether()/IPv6(src="<ipv6 src change inputset>", dst="<ipv6 dst>")/IPv6ExtHdrFragment()/("X"*480)], iface="<tester interface>")
+ >>> sendp([Ether()/IPv6(src="<ipv6 src>", dst="<ipv6 dst change inputset>")/IPv6ExtHdrFragment()/("X"*480)], iface="<tester interface>")
+
+
+Test Case 4: MAC_IPV6_TCP
+-------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv6 dst is <ipv6 dst> tc is <tc> / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv6 dst is <ipv6 dst> tc is <tc> / tcp src is <sport> dst is <dport> / end actions queue index 3 / end
+
+matched packets::
+
+ >>> sendp([Ether()/IPv6(src="<ipv6 src>",dst="<ipv6 dst>",tc=<tc>)/TCP(sport=<sport>,dport=23)/Raw("x"*80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether()/IPv6(src="<ipv6 src>",dst="<ipv6 dst change inputset>",tc=<tc>)/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IPv6(src="<ipv6 src>",dst="<ipv6 dst>",tc=<tc change inputset>)/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IPv6(src="<ipv6 src>",dst="<ipv6 dst>",tc=<tc>)/TCP(sport=<sport change inputset>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IPv6(src="<ipv6 src>",dst="<ipv6 dst>",tc=<tc>)/TCP(sport=<sport>,dport=<dport change inputset>)/Raw("x"*80)],iface="<tester interface>",count=1)
+
+
+Test Case 5: MAC_IPV4_VXLAN_IPV4_FRAG
+-------------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions rss queues 2 3 end / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 5 / end
+
+matched packets::
+
+ >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>",frag=5)/Raw("x"*80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src change inputset>", dst="<ipv4 dst>",frag=5)/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst change inputset>",frag=5)/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>",frag=5)/Raw("x"*80)],iface="<tester interface>",count=1)
+
+
+Test Case 6: MAC_IPV4_VXLAN_IPV4_PAY
+------------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 5 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions rss queues 2 3 end / end
+
+matched packets::
+
+ >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>")/TCP()/Raw("x"*80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src change inputset>", dst="<ipv4 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst change inputset>")/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src change inputset>", dst="<ipv4 dst>")/TCP()/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst change inputset>")/TCP()/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>", dst="<ipv4 dst>")/TCP()/Raw("x"*80)],iface="<tester interface>",count=1)
+
+
+Test Case 7: MAC_IPV4_NVGRE_MAC_IPV4_UDP_PAY
+--------------------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 dst is <ipv4 dst> / nvgre tni is <tni> / eth dst is <dst mac> / ipv4 src is <inner ipv4 src> dst is <inner ipv4 dst> / udp src is <sport> dst is <dport> / end actions rss queues 2 3 end / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 dst is <ipv4 dst> / nvgre tni is <tni> / eth dst is <dst mac> / ipv4 src is <inner ipv4 src> dst is <inner ipv4 dst> / udp src is <sport> dst is <dport> / end actions queue index 4 / end
+
+matched packets::
+
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether()/IP(dst="<ipv4 dst change inputset>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni change inputset>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac change inputset>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src change inputset>", dst="<inner ipv4 dst>")/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst change inputset>")/UDP(sport=<sport>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/UDP(sport=<sport change inputset>,dport=<dport>)/Raw("x"*80)], iface="<tester interface>", count=1)
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/UDP(sport=<sport>,dport=<dport change inputset>)/Raw("x"*80)], iface="<tester interface>", count=1)
+
+
+Test Case 8: MAC_IPV4_NVGRE_MAC_IPV4_TCP
+----------------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 dst is <ipv4 dst> / nvgre tni is <tni> / eth dst is <dst mac> / ipv4 src is <inner ipv4 src> dst is <inner ipv4 dst> / tcp src is <sport> dst is <dport> / end actions queue index 5 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 dst is <ipv4 dst> / nvgre tni is <tni> / eth dst is <dst mac> / ipv4 src is <inner ipv4 src> dst is <inner ipv4 dst> / tcp src is <sport> dst is <dport> / end actions rss queues 2 3 end / end
+
+matched packets::
+
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether()/IP(dst="<ipv4 dst change inputset>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni change inputset>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac change inputset>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src change inputset>", dst="<inner ipv4 dst>")/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst change inputset>")/TCP(sport=<sport>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>", dst="<inner ipv4 dst>")/TCP(sport=<sport change inputset>,dport=<dport>)/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether()/IP(dst="<ipv4 dst>")/NVGRE(TNI=<tni>)/Ether(dst="<dst mac>")/IP(src="<inner ipv4 src>2", dst="<inner ipv4 dst>")/TCP(sport=<sport>,dport=<dport change inputset>)/Raw("x"*80)],iface="<tester interface>",count=1)
+
+
+Test Case 9: ethertype filter_PPPOED
+------------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth type is <ethertype> / end actions queue index 4 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth type is <ethertype> / end actions queue index 2 / end
+
+matched packets::
+
+ >>> sendp([Ether(dst="<dst mac>", type=<ethertype>)/Raw("x" *80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>")/PPPoED()/Raw("x" *80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether(dst="<dst mac>", type=<ethertype change inputset>)/Raw("x" *80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>")/PPPoE()/Raw("x" *80)],iface="<tester interface>",count=1)
+
+
+Test Case 10: MAC_VLAN_PPPOE_IPV4_PAY_session_id_proto_id
+---------------------------------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv4 proto_id> / end actions queue index 1 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv4 proto_id> / end actions queue index 2 / end
+
+matched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<proto_id>)/IP()/Raw("x"*80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci change inputset>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid change inputset>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6()/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+
+Test Case 11: MAC_VLAN_PPPOE_IPV6_PAY_session_id_proto_id
+---------------------------------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv6 proto_id> / end actions queue index 1 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv6 proto_id> / end actions queue index 2 / end
+
+matched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6()/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci change inputset>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid change inputset>)/PPP(proto=<ipv6 proto_id>)/IPv6()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+
+Test Case 12: MAC_PPPOE_IPV4_PAY_IP_address
+-------------------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / pppoes / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 1 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / pppoes / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 2 / end
+
+matched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=3)/PPP(proto=0x0021)/IP(src="<ipv4 src>", dst="<ipv4 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=3)/PPP(proto=0x0021)/IP(src="<ipv4 src change inputset>", dst="<ipv4 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=3)/PPP(proto=0x0021)/IP(src="<ipv4 src>", dst="<ipv4 dst change inputset>")/Raw("x"*80)],iface="<tester interface>",count=1)
+
+
+Test Case 13: MAC_PPPOE_IPV6_UDP_PAY
+------------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / pppoes / ipv6 dst is <ipv6 dst> / udp src is <sport> dst is <dport> / end actions queue index 1 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / pppoes / ipv6 dst is <ipv6 dst> / udp src is <sport> dst is <dport> / end actions queue index 2 / end
+
+matched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/UDP(sport=<sport>,dport=<dport>)/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src>", dst="<ipv6 dst change inputset>")/UDP(sport=<sport>,dport=<dport>)/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/UDP(sport=<sport change inputset>,dport=<dport>)/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/UDP(sport=<sport>,dport=<dport change inputset>)/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+
+Test Case 14: MAC_VLAN_PPPOE_IPV4_TCP_PAY_non_src_dst_port
+----------------------------------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / vlan tci is <tci> / pppoes / ipv4 src is <ipv4 src> dst is <ipv4 dst> / tcp / end actions queue index 1 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / vlan tci is <tci> / pppoes / ipv4 src is <ipv4 src> dst is <ipv4 dst> / tcp / end actions queue index 2 / end
+
+matched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP(src="<ipv4 src>", dst="<ipv4 dst>")/TCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci change inputset>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP(src="<ipv4 src>", dst="<ipv4 dst>")/TCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP(src="<ipv4 src change inputset>", dst="<ipv4 dst>")/TCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP(src="<ipv4 src>", dst="<ipv4 dst change inputset>")/TCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP(src="<ipv4 src>", dst="<ipv4 dst>")/UDP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP(src="<ipv4 src>", dst="<ipv4 dst>")/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+
+Test Case 15: MAC_VLAN_PPPOE_IPV6_PAY_IP_address
+------------------------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / vlan tci is <tci> / pppoes / ipv6 src is <ipv6 src> / end actions queue index 1 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / vlan tci is <tci> / pppoes / ipv6 src is <ipv6 src> / end actions queue index 2 / end
+
+matched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci change inputset>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src>", dst="<ipv6 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv6 proto_id>)/IPv6(src="<ipv6 src change inputset>", dst="<ipv6 dst>")/Raw("x"*80)],iface="<tester interface>",count=1)
+
+
+Test Case 16: MAC_PPPOE_LCP_PAY
+-------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / pppoes seid is <seid> / pppoe_proto_id is <LCP proto_id> / end actions queue index 1 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / pppoes seid is <seid> / pppoe_proto_id is <LCP proto_id> / end actions queue index 2 / end
+
+matched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid change inputset>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+
+Test Case 17: MAC_PPPOE_IPCP_PAY
+--------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / pppoes seid is <seid> / pppoe_proto_id is <IPCP proto_id> / end actions queue index 1 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / pppoes seid is <seid> / pppoe_proto_id is <IPCP proto_id> / end actions queue index 2 / end
+
+matched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid change inputset>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+
+Test Case 18: MAC_VLAN_PPPOE_LCP_PAY
+------------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <LCP proto_id> / end actions queue index 1 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <LCP proto_id> / end actions queue index 2 / end
+
+matched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci change inputset>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid change inputset>)/PPP(proto=<LCP proto_id>)/PPP_LCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+
+Test Case 19: MAC_VLAN_PPPOE_IPCP_PAY
+-------------------------------------
+rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <IPCP proto_id> / end actions queue index 1 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <IPCP proto_id> / end actions queue index 2 / end
+
+matched packets::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+mismatched packets::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci change inputset>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid change inputset>)/PPP(proto=<IPCP proto_id>)/PPP_IPCP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<tci>,type=0x8864)/PPPoE(sessionid=<seid>)/PPP(proto=<ipv4 proto_id>)/IP()/Raw("x" * 80)],iface="<tester interface>",count=1)
+
+
+Test Case 20: check non-pipeline mode flow priority filter
+----------------------------------------------------------
+This case is designed to check a flow with priority = 1 will be programmed into switch filter,
+a flow with priority = 0 will be programmed into switch first then fdir
+
+Test Steps
+~~~~~~~~~~
+1. launch testpmd with --log-level="ice,8"
+
+2. create rules with priority 0, check the rule is created to switch with a log "Succeeded to create (2) flow"::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 dst is <ipv4 src> / nvgre tni is <tni> / eth / ipv4 src is <inner ipv4 src> dst is <inner ipv4 dst> / end actions queue index 3 / end
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / end
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv6 proto_id> / end actions drop / end
+
+3. create rules with priority 0, and the action is mark, check the rule is created to fdir with a log "Succeeded to create (1) flow"::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / mark id 3 / end
+
+4. create rules with priority 1, check the rule is created to switch with a log "Succeeded to create (2) flow"::
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / end
+ testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv6 proto_id> / end actions drop / end
+
+5. create rules with priority 1, and the action is mark, check the rule create fail::
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 dst is <ipv4 src> / nvgre tni is <tni> / eth / ipv4 src is <inner ipv4 src> dst is <inner ipv4 dst> / end actions queue index 3 / mark id 3 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / mark id 3 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth dst is <dst mac> / vlan tci is <tci> / pppoes seid is <seid> / pppoe_proto_id is <ipv6 proto_id> / end actions drop / mark id 3 / end
+
+
+Test Case 21: negative test cases
+---------------------------------
+Test Steps
+~~~~~~~~~~
+1. create rules, check all these rules can not be created::
+
+ testpmd> flow create 0 priority 2 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 3 / end
+ testpmd> flow create 0 priority a ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 3 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions mark / rss / end
+
+
+Test Case 22: non-pipeline mode exclusive test cases
+----------------------------------------------------
+This case is designed to check some exclusive scenario in non-pipeline mode.
+
+Subcase 1: same pattern/input set/action different priority
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+1. create same pattern, input set and action but different priority, check these two rules can be created::
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 3 / end
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 3 / end
+
+2. send matched packet and check queue 3 receive this packet::
+
+ >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/TCP()/("X"*480)], iface="<tester interface>", count=1)
+
+3. destroy rules::
+
+ testpmd> flow flush 0
+
+Subcase 2: same pattern/input set/priority different action
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+1. create same pattern, input set and priority but different action, check the second rule can not be created::
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 3 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions rss queues 4 5 end / end
+
+Subcase 3: some rules overlap
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+1. create rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / vlan / vlan / pppoes / pppoe_proto_id is 0x21 / end actions queue index 3 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / vlan / vlan / pppoes seid is 1 / ipv4 / end actions queue index 2 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / vlan / vlan tci is 12 / end actions queue index 4 / end
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is 00:00:00:01:03:13 / vlan / vlan / end actions rss queues 1 2 end / end
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is 00:00:00:01:03:03 / end actions queue index 8 / end
+ testpmd> flow create 0 priority 1 ingress pattern eth / vlan tci is 1 / vlan tci is 2 / end actions queue index 4 / end
+
+2. check all the rules exist in the list::
+
+ testpmd> flow list 0
+
+3. send packet which match rule 0 and rule 1, check the packet can be received by queue 3::
+
+ >>> sendp([Ether(type=0x8100)/Dot1Q(vlan=1,type=0x8100)/Dot1Q(vlan=0x2,type=0x8864)/PPPoE(sessionid=0x1)/PPP(proto=0x21)/IP()/UDP(dport=23)/("X"*480)], iface="<tester interface>")
+
+4. destroy rule 0, repeat step 3 and check the packet can be received by queue 2::
+
+ testpmd> flow destroy 0 rule 0
+
+5. send packet which match rule 2 and rule 3, check the packet can be received by queue 1 or 2::
+
+ >>> sendp([Ether(dst="00:00:00:01:03:13")/Dot1Q(vlan=1)/Dot1Q(vlan=12)/Raw("x"*480)], iface="<tester interface>", count=1)
+
+6. destroy rule 3, repeat step 5 and check the packet can be received by queue 4::
+
+ testpmd> flow destroy 0 rule 3
+
+7. send packet which match rule 4 and rule 5, check the packet will be received by queue 8::
+
+ >>> sendp([Ether(dst="00:00:00:01:03:03")/Dot1Q(vlan=1)/Dot1Q(vlan=2)/Raw("x"*480)], iface="<tester interface>", count=1)
+
+8. destroy rule 4, repeat step 7 and check the packet can be received by queue 4::
+
+ testpmd> flow destroy 0 rule 3
+
+
+Test Case 23: Create Flow Rules with Priority in Pipeline Mode
+--------------------------------------------------------------
+Priority is active in pipeline mode.
+This case is designed to check creating flow rules and setting priority 0/1 will map switch/fdir filter separately.
+Patterns in this case::
+
+ MAC_IPV4_TCP
+ MAC_IPV4_VXLAN_IPV4_UDP_PAY
+
+Test Steps
+~~~~~~~~~~
+1. Start the ``testpmd`` application as follows::
+
+ <dpdk build dir>/app/dpdk-testpmd <EAL options> -a <DUT port pci device id>,pipeline-mode-support=1 --log-level="ice,7" -- -i --rxq=<queue number> --txq=<queue number>
+ testpmd> set fwd rxonly
+ testpmd> set verbose 1
+ testpmd> rx_vxlan_port add 4789 0
+
+2. Create switch filter rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> / tcp src is <sport> dst is <dport> / end actions queue index 1 / end
+ ice_flow_create(): Succeeded to create (2) flow
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> / udp src is <sport> dst is <dport> / end actions queue index 2 / end
+ ice_flow_create(): Succeeded to create (2) flow
+
+3. Create fdir filter rules::
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is <ipv4 src change inputset> dst is <ipv4 dst change inputset> tos is <tos> ttl is <ttl> / tcp src is <sport> dst is <dport> / end actions queue index 3 / end
+ ice_flow_create(): Succeeded to create (1) flow
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is <ipv4 src change inputset> dst is <ipv4 dst change inputset> / udp src is <sport> dst is <dport> / end actions queue index 4 / end
+ ice_flow_create(): Succeeded to create (1) flow
+
+4. Check flow list with commands "flow list 0", all flows are created correctly::
+
+ +-----+--------+--------+--------+-----------------------+
+ |ID | Group | Prio | Attr | Rul |
+ +=====+========+========+========+=======================+
+ | 0 | 0 | 0 | i- | ETH IPV4 TCP => QUEUE |
+ +-----+--------+--------+--------+-----------------------+
+ | 1 ... |
+ +-----+--------+--------+--------+-----------------------+
+ | 2 ... |
+ +-----+--------+--------+--------+-----------------------+
+ | 3 ... |
+ +-----+--------+--------+--------+-----------------------+
+
+5. Send packets according to the created rules in tester::
+
+ >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>)/TCP(sport=<sport>,dport=<dport>)/Raw('x'*80)],iface="<tester interface>")
+ >>> sendp([Ether(dst="<dst mac>")/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>)/UDP(sport=<sport>,dport=<dport>)/Raw('x'*80)],iface="<tester interface>")
+ >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src change inputset>",dst="<ipv4 dst change inputset>",tos=<tos>,ttl=<ttl>)/TCP(sport=<sport>,dport=<dport>)/Raw('x'*80)],iface="<tester interface>")
+ >>> sendp([Ether(dst="<dst mac>")/IP()/UDP()/VXLAN()/Ether()/IP(src="<ipv4 src change inputset>",dst="<ipv4 dst change inputset>")/UDP(sport=<sport>,dport=<dport>)/Raw('x'*80)],iface="<tester interface>")
+
+6. Check the packets are recieved in right queues by dut::
+
+ testpmd> port 0/queue 1: received 1 packets
+ src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0x96803f93 - RSS queue=0x1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x1
+ ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
+ ......
+
+7. Create rules without priority, Check only patterns supported by switch can be created for the default priorty is 0.
+ So the first flow can be created and the second flow can not be created::
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 src is 192.168.0.3 dst is 192.168.0.1 tos is 5 / tcp src is 25 dst is 23 / end actions queue index 1 / end
+ ice_flow_create(): Succeeded to create (2) flow
+ Flow rule #1 created
+ testpmd> flow create 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 ttl is 20 / sctp src is 25 dst is 23 / end actions queue index 1 / end
+ ice_flow_create(): Failed to create flow
+ Caught error type 2 (flow rule (handle)): Invalid input pattern: Invalid argument
+
+
+Test case 24: Create Flow Rules Only Supported by Fdir Filter with Priority 0 in Pipeline Mode
+----------------------------------------------------------------------------------------------
+Creating a rule only supported by fdir filter with priority 0, it is not acceptable.
+Patterns in this case::
+
+ MAC_IPV6_SCTP
+ MAC_IPV4_SCTP
+
+Test Steps
+~~~~~~~~~~
+1. Start the ``testpmd`` application as follows::
+
+ <dpdk build dir>/app/dpdk-testpmd <EAL options> -a <DUT port pci device id>,pipeline-mode-support=1 --log-level="ice,7" -- -i --rxq=<queue number> --txq=<queue number>
+ testpmd> set fwd rxonly
+ testpmd> set verbose 1
+
+2. Create rules, check the flows can not be created::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv6 src is 1111:2222:3333:4444:5555:6666:7777:8888 dst is 1111:2222:3333:4444:5555:6666:7777:9999 / sctp src is 25 dst is 23 / end actions queue index 1 / end
+ ice_flow_create(): Failed to create flow
+ Caught error type 2 (flow rule (handle)): Invalid input pattern: Invalid argument
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 ttl is 20 / sctp src is 25 dst is 23 / end actions queue index 1 / end
+ ice_flow_create(): Failed to create flow
+ Caught error type 2 (flow rule (handle)): Invalid input pattern: Invalid argument
+
+
+Test case 25: Create flow rules only supported by switch filter with priority 1 in Pipeline Mode
+------------------------------------------------------------------------------------------------
+Create a rule only supported by fdir switch with priority 1, it is not acceptable.
+Patterns in this case::
+
+ MAC_IPV4_NVGRE_MAC_IPV4
+ MAC_IPV4_NVGRE_MAC_IPV4_UDP
+
+Test Steps
+~~~~~~~~~~
+1. Start the ``testpmd`` application as follows::
+
+ <dpdk build dir>/app/dpdk-testpmd <EAL options> -a <DUT port pci device id>,pipeline-mode-support=1 --log-level="ice,7" -- -i --rxq=<queue number> --txq=<queue number>
+ testpmd> set fwd rxonly
+ testpmd> set verbose 1
+
+2. Create rules, check the flows can not be created::
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / nvgre / eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 3 / end
+ ice_flow_create(): Failed to create flow
+ Caught error type 13 (specific pattern item): cause: 0x7fffe65b8128, Unsupported pattern: Invalid argument
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / nvgre / eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / udp src is 25 dst is 23 / end actions queue index 3 / end
+ ice_flow_create(): Failed to create flow
+ Caught error type 13 (specific pattern item): cause: 0x7fffe65b8128, Unsupported pattern: Invalid argument
+
+
+Test case 26: Create flow rules with same parameter but differenet actions in Pipeline Mode
+-------------------------------------------------------------------------------------------
+It is acceptable to create same rules with differenet filter in pipeline mode.
+When fdir filter and switch filter has the same parameter rules, the flow will map to switch then fdir.
+Patterns in this case::
+
+ MAC_IPV4_TCP
+
+Test Steps
+~~~~~~~~~~
+1. Start the ``testpmd`` application as follows::
+
+ <dpdk build dir>/app/dpdk-testpmd <EAL options> -a <DUT port pci device id>,pipeline-mode-support=1 --log-level="ice,7" -- -i --rxq=<queue number> --txq=<queue number>
+ testpmd> set fwd rxonly
+ testpmd> set verbose 1
+
+2. Create switch rule then fdir rule with the same parameter, check two flows can be created::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> / tcp src is <sport> dst is <dport> / end actions queue index 1 / end
+ ice_flow_create(): Succeeded to create (2) flow
+ Flow rule #0 created
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> / tcp src is <sport> dst is <dport> / end actions queue index 3 / end
+ ice_interrupt_handler(): OICR: MDD event
+ ice_flow_create(): Succeeded to create (1) flow
+ Flow rule #1 created
+
+3. Tester send a packet to dut::
+
+ >>> sendp([Ether(dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>",tos=<tos>)/TCP(sport=<sport>,dport=<dport>)/Raw('x'*80)],iface="<tester interface>")
+
+4. Check the packets are recieved by dut in queue 1::
+
+ testpmd> port 0/queue 1: received 1 packets
+ src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x1
+ ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
+
+5. Remove the switch rule::
+
+ testpmd> flow destroy 0 rule 0
+
+6. Repeat step 3.
+
+7. Check the packets are recieved in queue 3::
+
+ testpmd> port 0/queue 3: received 1 packets
+ src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x3 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x3
+ ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
+
+8. Restart the ``testpmd`` application as follows::
+
+ <dpdk build dir>/app/dpdk-testpmd <EAL options> -a <DUT port pci device id>,pipeline-mode-support=1 --log-level="ice,7" -- -i --rxq=<queue number> --txq=<queue number>
+ testpmd> set fwd rxonly
+ testpmd> set verbose 1
+
+9. Create fdir rule then switch rule with the same parameter, check two flows can be created::
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> / tcp src is <sport> dst is <dport> / end actions queue index 3 / end
+ ice_interrupt_handler(): OICR: MDD event
+ ice_flow_create(): Succeeded to create (1) flow
+ Flow rule #0 created
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> tos is <tos> / tcp src is <sport> dst is <dport> / end actions queue index 1 / end
+ ice_flow_create(): Succeeded to create (2) flow
+ Flow rule #1 created
+
+10. Repeat step 3.
+
+11. Check the packets are recieved by dut in queue 1::
+
+ testpmd> port 0/queue 1: received 1 packets
+ src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x1
+ ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
+
+12. Remove the switch rule::
+
+ testpmd> flow destroy 0 rule 1
+
+13. Repeat step 3.
+
+14. Check the packets are recieved in queue 3::
+
+ testpmd> port 0/queue 3: received 1 packets
+ src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x3 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x3
+ ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
\ No newline at end of file
deleted file mode 100644
@@ -1,338 +0,0 @@
-.. Copyright (c) <2019>, Intel Corporation
- All rights reserved.
-
- Redistribution and use in source and binary forms, with or without
- modification, are permitted provided that the following conditions
- are met:
-
- - Redistributions of source code must retain the above copyright
- notice, this list of conditions and the following disclaimer.
-
- - Redistributions in binary form must reproduce the above copyright
- notice, this list of conditions and the following disclaimer in
- the documentation and/or other materials provided with the
- distribution.
-
- - Neither the name of Intel Corporation nor the names of its
- contributors may be used to endorse or promote products derived
- from this software without specific prior written permission.
-
- THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
- COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
- INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
- (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
- HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
- STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
- ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
- OF THE POSSIBILITY OF SUCH DAMAGE.
-
-
-=======================
-Rte_flow Priority Tests
-=======================
-
-
-Description
-===========
-
-This document provides the plan for testing the Rte_flow Priority feature.
-this feature uses devargs as a hint to active flow priority or not.
-
-This test plan is based on Intel E810 series ethernet cards.
-when priority is not active, flows are created on fdir then switch/ACL.
-when priority is active, flows are identified into 2 category:
-High priority as permission stage that maps to switch/ACL,
-Low priority as distribution stage that maps to fdir,
-a no destination high priority rule is not acceptable, since it may be overwritten by a low priority rule due to cvl FXP behavior.
-
-Note: Since these tests are focus on priority, the patterns in tests are examples.
-
-
-Prerequisites
-=============
-
-Bind the pf to dpdk driver::
-
- ./usertools/dpdk-devbind.py -b vfio-pci af:00.0
-
-Note: The kernel must be >= 3.6+ and VT-d must be enabled in bios.
-
-Test Case: Setting Priority in Non-pipeline Mode
-================================================
-
-Priority is not active in non-pipeline mode. The default value of priority is 0 but it will be ignored.
-
-Patterns in this case:
- MAC_IPV4
-
-#. Start the ``testpmd`` application as follows::
-
- ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0xf -n 4 -a 0000:af:00.0 --log-level="ice,7" -- -i --txq=8 --rxq=8
- set fwd rxonly
- set verbose 1
-
-#. Create a rule with priority 0, Check the flow can be created but it will map to fdir filter::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 2 / mark / end
- ice_interrupt_handler(): OICR: MDD event
- ice_flow_create(): Succeeded to create (1) flow
- Flow rule #0 created
-
-#. Create a rule with priority 1, check the flow can not be created for the vallue of priority is 0 in non-pipeline mode::
-
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 2 / mark / end
- ice_flow_create(): Failed to create flow
- Caught error type 4 (priority field): cause: 0x7ffe24e65738, Not support priority.: Invalid argument
-
-#. Start the ``testpmd`` application as follows::
-
- ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0xf -n 4 -a 0000:af:00.0,pipeline-mode-support=0 --log-level="ice,7" -- -i --txq=8 --rxq=8
- set fwd rxonly
- set verbose 1
-
-#. Create a rule with priority 0, Check the flow can be created but it will map to fdir filter::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 2 / end
- ice_interrupt_handler(): OICR: MDD event
- ice_flow_create(): Succeeded to create (1) flow
- Flow rule #0 created
-
-#. Create a rule with priority 1, check the flow can not be created for the vallue of priority is 0 in non-pipeline mode::
-
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 2 / end
- ice_flow_create(): Failed to create flow
- Caught error type 4 (priority field): cause: 0x7ffe24e65738, Not support priority.: Invalid argument
-
-Test Case: Create Flow Rules with Priority in Pipeline Mode
-============================================================
-
-Priority is active in pipeline mode.
-Creating flow rules and setting priority 0/1 will map switch/fdir filter separately.
-
-Patterns in this case:
- MAC_IPV4_TCP
- MAC_IPV4_VXLAN_IPV4_UDP_PAY
-
-#. Start the ``testpmd`` application as follows::
-
- ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0xf -n 4 -a 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
- set fwd rxonly
- set verbose 1
- rx_vxlan_port add 4789 0
-
-#. Create switch filter rules::
-
- flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions queue index 1 / end
-
- flow create 0 priority 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / udp src is 25 dst is 23 / end actions queue index 2 / end
-
-#. Create fdir filter rules::
-
- flow create 0 priority 1 ingress pattern eth / ipv4 src is 192.168.0.4 dst is 192.168.0.7 tos is 4 ttl is 20 / tcp src is 25 dst is 23 / end actions queue index 3 / end
-
- flow create 0 priority 1 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is 192.168.0.4 dst is 192.168.0.7 / udp src is 25 dst is 23 / end actions queue index 4 / end
-
-#. Check flow list with commands "flow list 0", all flows are created correctly::
-
- +-----+--------+--------+--------+-----------------------+
- |ID | Group | Prio | Attr | Rul |
- +=====+========+========+========+=======================+
- | 0 | 0 | 0 | i- | ETH IPV4 TCP => QUEUE |
- +-----+--------+--------+--------+-----------------------+
- | 1 ... |
- +-----+--------+--------+--------+-----------------------+
- | 2 ... |
- +-----+--------+--------+--------+-----------------------+
- | 3 ... |
- +-----+--------+--------+--------+-----------------------+
-
-#. Send packets according to the created rules in tester::
-
- sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
- sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP()/UDP()/VXLAN()/Ether()/IP(src="192.168.0.2",dst="192.168.0.3",tos=4)/UDP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
- sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.168.0.4",dst="192.168.0.7",tos=4,ttl=20)/TCP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
- sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP()/UDP()/VXLAN()/Ether()/IP(src="192.168.0.4 ",dst="192.168.0.7")/UDP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
-
-#. Check the packets are recieved in right queues by dut::
-
- testpmd> port 0/queue 1: received 1 packets
- src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0x96803f93 - RSS queue=0x1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x1
- ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
- ......
-
-#. Create rules without priority, Check only patterns supported by switch can be created for the default priorty is 0.
-So the first flow can be created and the second flow can not be created::
-
- testpmd> flow create 0 ingress pattern eth / ipv4 src is 192.168.0.3 dst is 192.168.0.1 tos is 5 / tcp src is 25 dst is 23 / end actions queue index 1 / end
- ice_flow_create(): Succeeded to create (2) flow
- Flow rule #1 created
- testpmd> flow create 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 ttl is 20 / sctp src is 25 dst is 23 / end actions queue index 1 / end
- ice_flow_create(): Failed to create flow
- Caught error type 2 (flow rule (handle)): Invalid input pattern: Invalid argument
-
-Test case: Create No Destination High Priority Flow Rule
-========================================================
-
-A no destination high priority rule is not acceptable. Destination here means exact actions.
-
-Patterns in this case:
- MAC_IPV4_TCP
-
-#. Start the ``testpmd`` application as follows::
-
- ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0xf -n 4 -a 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
- set fwd rxonly
- set verbose 1
-
-#. Create a rule without exact actions, check the flows can not be created::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions / end
- Bad arguments
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end
- Bad arguments
-
-Test case: Create Flow Rules Only Supported by Fdir Filter with Priority 0
-===========================================================================
-
-Creating a rule only supported by fdir filter with priority 0, it is not acceptable.
-
-Patterns in this case:
- MAC_IPV6_SCTP
- MAC_IPV4_SCTP
-
-#. Start the ``testpmd`` application as follows::
-
- ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0xf -n 4 -a 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
- set fwd rxonly
- set verbose 1
-
-#. Create rules, check the flows can not be created::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv6 src is 1111:2222:3333:4444:5555:6666:7777:8888 dst is 1111:2222:3333:4444:5555:6666:7777:9999 / sctp src is 25 dst is 23 / end actions queue index 1 / end
- ice_flow_create(): Failed to create flow
- Caught error type 2 (flow rule (handle)): Invalid input pattern: Invalid argument
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 ttl is 20 / sctp src is 25 dst is 23 / end actions queue index 1 / end
- ice_flow_create(): Failed to create flow
- Caught error type 2 (flow rule (handle)): Invalid input pattern: Invalid argument
-
-
-Test case: Create flow rules only supported by switch filter with priority 1
-=============================================================================
-
-Create a rule only supported by fdir switch with priority 1, it is not acceptable.
-
-Patterns in this case:
- MAC_IPV4_NVGRE_MAC_IPV4
- MAC_IPV4_NVGRE_MAC_IPV4_UDP
-
-#. Start the ``testpmd`` application as follows::
-
- ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0xf -n 4 -a 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
- set fwd rxonly
- set verbose 1
-
-#. Create rules, check the flows can not be created::
-
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / nvgre / eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 3 / end
- ice_flow_create(): Failed to create flow
- Caught error type 13 (specific pattern item): cause: 0x7fffe65b8128, Unsupported pattern: Invalid argument
-
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / nvgre / eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / udp src is 25 dst is 23 / end actions queue index 3 / end
- ice_flow_create(): Failed to create flow
- Caught error type 13 (specific pattern item): cause: 0x7fffe65b8128, Unsupported pattern: Invalid argument
-
-Test case: Create flow rules with same parameter but differenet actions
-==========================================================================
-
-It is acceptable to create same rules with differenet filter in pipeline mode.
-When fdir filter and switch filter has the same parameter rules, the flow will map to switch then fdir.
-
-Patterns in this case:
- MAC_IPV4_TCP
-
-#. Start the ``testpmd`` application as follows::
-
- ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0xf -n 4 -a 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
- set fwd rxonly
- set verbose 1
-
-#. Create switch rule then fdir rule with the same parameter, check two flows can be created::
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions queue index 1 / end
- ice_flow_create(): Succeeded to create (2) flow
- Flow rule #0 created
-
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions queue index 3 / end
- ice_interrupt_handler(): OICR: MDD event
- ice_flow_create(): Succeeded to create (1) flow
- Flow rule #1 created
-
-#. Tester send a pkt to dut::
-
- sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
-
-#. Check the packets are recieved by dut in queue 1::
-
- testpmd> port 0/queue 1: received 1 packets
- src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x1
- ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
-
-#. Remove the switch rule::
-
- testpmd>flow destroy 0 rule 0
-
-#. Tester send a pkt to dut::
-
- sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
-
-#. Check the packets are recieved in queue 3::
-
- testpmd> port 0/queue 3: received 1 packets
- src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x3 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x3
- ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
-
-#. Restart the ``testpmd`` application as follows::
-
- ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0xf -n 4 -a 0000:af:00.0, pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
- set fwd rxonly
- set verbose 1
-
-#. Create fdir rule then switch rule with the same parameter, check two flows can be created::
-
- testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions queue index 3 / end
- ice_interrupt_handler(): OICR: MDD event
- ice_flow_create(): Succeeded to create (1) flow
- Flow rule #0 created
-
- testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions queue index 1 / end
- ice_flow_create(): Succeeded to create (2) flow
- Flow rule #1 created
-
-#. Tester send a pkt to dut::
-
- sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
-
-#. Check the packets are recieved by dut in queue 1::
-
- testpmd> port 0/queue 1: received 1 packets
- src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x1
- ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
-
-#. Remove the switch rule::
-
- testpmd>flow destroy 0 rule 1
-
-#. Tester send a pkt to dut::
-
- sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
-
-#. Check the packets are recieved in queue 3::
-
- testpmd> port 0/queue 3: received 1 packets
- src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x3 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x3
- ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN