diff mbox series

[V4,1/3] test_plans: add iavf_checksum_offload_perf test plan

Message ID 20230518024014.120638-2-yingyax.han@intel.com (mailing list archive)
State Accepted
Headers
Series add iavf_checksum_offload_perf test suite |

Commit Message

Yingya Han May 18, 2023, 2:40 a.m. UTC 
  Signed-off-by: Yingya Han <yingyax.han@intel.com>
---
 .../iavf_checksum_offload_perf_test_plan.rst  | 216 ++++++++++++++++++
 test_plans/index.rst                          |   1 +
 2 files changed, 217 insertions(+)
 create mode 100644 test_plans/iavf_checksum_offload_perf_test_plan.rst
diff mbox series

Patch

diff --git a/test_plans/iavf_checksum_offload_perf_test_plan.rst b/test_plans/iavf_checksum_offload_perf_test_plan.rst
new file mode 100644
index 00000000..bd5ebd50
--- /dev/null
+++ b/test_plans/iavf_checksum_offload_perf_test_plan.rst
@@ -0,0 +1,216 @@ 
+.. SPDX-License-Identifier: BSD-3-Clause
+   Copyright(c) 2023 Intel Corporation
+
+=====================================================
+Benchmark the performance of iavf checksum forwarding
+=====================================================
+
+Description
+===========
+
+Send packets with incorrect checksum,
+verify dpdk can rx it and report the checksum error,
+verify that the same number of packet are correctly received on the traffic
+generator side.
+
+Prerequisites
+=============
+
+1. Hardware:
+
+   I40E driver NIC (Intel® Ethernet 700 Series XXV710, XL710, X710)
+   ICE driver NIC (Intel® Ethernet 800 Series E810-CQDA2, E810-XXVDA4)
+
+2. Software::
+
+    dpdk: git clone http://dpdk.org/git/dpdk
+    trex: git clone http://trex-tgn.cisco.com/trex/release/v2.93.tar.gz
+
+
+Test Case
+=========
+The test case check the throughput result with ipv4, in the case,
+we will send the bi-direction flows with line rate, then we can check the
+passthrough rate.
+
+Common Steps
+------------
+1. Bind PF ports to kernel driver(ice), then create 1 VF from each PF,
+   take E810-CQDA2 for example::
+
+    echo 1 > /sys/bus/pci/devices/0000\:17\:00.0/sriov_numvfs
+    echo 1 > /sys/bus/pci/devices/0000\:4b\:00.0/sriov_numvfs
+
+2. Ip link set VF trust on and spoofchk off on DUT::
+
+    ip link set $PF_INTF vf 0 trust on
+    ip link set $PF_INTF vf 0 spoofchk off
+
+3. Set vf mac address::
+
+    ip link set ens5f0 vf 0 mac 00:12:34:56:78:01
+    ip link set ens6f0 vf 0 mac 00:12:34:56:78:02
+
+4. Bind tested ports to vfio-pci::
+
+    <dpdk_dir>#./usertools/dpdk-devbind.py -s
+    0000:17:00.0 'Device 1592' if=ens5f0 drv=ice unused=vfio-pci
+    0000:4b:00.0 'Device 1592' if=ens6f0 drv=ice unused=vfio-pci
+    <dpdk_dir>#./usertools/dpdk-devbind.py -b vfio-pci <pci device id>
+    <dpdk_dir>#./usertools/dpdk-devbind.py -b vfio-pci 0000:17:01.0
+    <dpdk_dir>#./usertools/dpdk-devbind.py -b vfio-pci 0000:4b:01.0
+
+5. Start dpdk-testpmd::
+
+     <build_dir>/app/dpdk-testpmd -l 5,6 -n 8 --force-max-simd-bitwidth=512 \
+     -- -i --portmask=0x3 --rxq=1 --txq=1 --txd=1024 --rxd=1024 --forward=io \
+     --nb-cores=1 --enable-rx-cksum
+
+    Note:
+      -force-max-simd-bitwidth: set 512
+      -enable-rx-cksum: enable rx checksum
+
+6. Configure traffic generator to send traffic
+
+    Test flow MAC table.
+
+    +------+---------+------------+----------------+
+    | Flow | Traffic | MAC        | MAC            |
+    |      | Gen.    | Src.       | Dst.           |
+    |      | Port    | Address    | Address        |
+    +======+=========+============+================+
+    |   1  |   TG0   | Random MAC | 00:12:34:56:01 |
+    +------+---------+------------+----------------+
+    |   2  |   TG1   | Random Mac | 00:12:34:56:02 |
+    +------+---------+------------+----------------+
+
+    The Flow IP table.
+
+    +------+---------+------------+------------+
+    | Flow | Traffic | IPV4       | IPV4       |
+    |      | Gen.    | Src.       | Dest.      |
+    |      | Port    | Address    | Address    |
+    +======+=========+============+============+
+    |   1  |   TG0   | Any IP     | 198.18.1.0 |
+    +------+---------+------------+------------+
+    |   2  |   TG1   | Any IP     | 198.18.0.0 |
+    +------+---------+------------+------------+
+
+    Set the packet length : 128 bytes-1518 bytes
+    The IPV4 Dest Address increase with the num 1024.
+
+7. Test results table.
+
+    +-----------+------------+-------------+---------+
+    |  Fwd_core | Frame Size |  Throughput |   Rate  |
+    +===========+============+=============+=========+
+    |  1C/1T    |    128     |  xxxxx Mpps |   xxx % |
+    +-----------+------------+-------------+---------+
+    |  1C/1T    |   ...      |  xxxxx Mpps |   xxx % |
+    +-----------+------------+-------------+---------+
+
+Test Case 1: test_perf_disable_checksum_offload_ipv4
+----------------------------------------------------
+
+1. Repeat common step 1-5.
+
+2. Configure traffic generator to send traffic as common step 6.
+
+3. Record Test results as common step 7.
+
+4. Config SW checksum offload::
+
+    testpmd>stop
+    testpmd>set fwd csum
+    testpmd>port stop all
+    testpmd>csum set ip sw 0
+    testpmd>csum set ip sw 1
+    testpmd>port start all
+    testpmd>start
+
+5. Configure traffic generator to send traffic as common step 6.
+
+   And configure the correct or incorrect ipv4 checksum separately.
+
+6. Record Test results as common step 7.
+
+Test Case 2: test_perf_disable_checksum_offload_vxlan
+-----------------------------------------------------
+
+1. Repeat common step 1-5.
+
+2. Config SW checksum offload::
+
+    testpmd>stop
+    testpmd>set fwd csum
+    testpmd>port stop all
+    testpmd>csum set ip sw 0
+    testpmd>csum set ip sw 1
+    testpmd>port start all
+    testpmd>start
+
+3. Set the traffic flow as below:
+
+    Ether / IPv4 / UDP / VXLAN / Ether / IPv4 / UDP / payload
+
+    Set the packet length : 128 bytes-1518 bytes.
+
+    Configure the correct or incorrect inner and outer ipv4 checksum and udp checksum separately.
+
+4. Record Test results as common step 7.
+
+Test Case 3: test_perf_enable_checksum_offload_ipv4
+---------------------------------------------------
+
+1. Repeat common step 1-5.
+
+2. Config HW checksum offload::
+
+    testpmd>stop
+    testpmd>set fwd csum
+    testpmd>port stop all
+    testpmd>csum set ip hw 0
+    testpmd>csum set ip hw 1
+    testpmd>port start all
+    testpmd>set promisc all on
+    testpmd>start
+
+3. Configure traffic generator to send traffic as common step 6.
+
+   And configure the correct or incorrect ipv4 checksum separately.
+
+5. Record Test results as common step 7.
+
+Test Case 4: test_perf_enable_checksum_offload_vxlan
+----------------------------------------------------
+
+1. Repeat common step 1-5.
+
+2. Config HW checksum offload::
+
+    testpmd>stop
+    testpmd>set fwd csum
+    testpmd>port stop all
+    testpmd>csum set ip hw 0
+    testpmd>csum set ip hw 1
+    testpmd>csum set udp hw 0
+    testpmd>csum set udp hw 1
+    testpmd>csum set outer-ip hw 0
+    testpmd>csum set outer-ip hw 1
+    testpmd>csum set outer-udp hw 0
+    testpmd>csum set outer-udp hw 1
+    testpmd>csum parse-tunnel on 0
+    testpmd>csum parse-tunnel on 1
+    testpmd>port start all
+    testpmd>set promisc all on
+    testpmd>start
+
+3. Set the traffic flow as below:
+
+    Ether / IPv4 / UDP / VXLAN / Ether / IPv4 / UDP / payload
+
+    Set the packet length : 128 bytes-1518 bytes.
+
+    Configure the correct or incorrect inner and outer ipv4 checksum and udp checksum separately.
+
+4. Record Test results as common step 7.
diff --git a/test_plans/index.rst b/test_plans/index.rst
index a0c056cd..8e10a7d5 100644
--- a/test_plans/index.rst
+++ b/test_plans/index.rst
@@ -80,6 +80,7 @@  The following are the test plans for the DPDK DTS automated test system.
     hotplug_test_plan
     ice_iavf_fdir_test_plan
     ice_iavf_fdir_gtpogre_test_plan
+    iavf_checksum_offload_perf_test_plan
     iavf_flexible_descriptor_test_plan
     iavf_package_driver_error_handle_test_plan
     iavf_fdir_protocol_agnostic_flow_test_plan